Country Clipper Jazee Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 19

Country Clipper Jazee Скачать руководство пользователя страница 13

9. JOYSTICK CONTROL LEVER

SENSITIVITY ADJUSTMENT

To change the sideways turning
response adjust as follows:

A.

Remove the right hand fender skirt
exposing the Joystick Control Lever
assembly.

B.

Remove the cross bolt, nut, and
spacers

C.

Reassemble the spacers as desired.
(2) spacers between the rod end ball
joints and the joystick pivot shaft will
quicken the side to-side-response, (1)
spacer slows the response.

P-11776

14

NOTE: It is important that there is at least one

spacer on each side of the rod end ball
joints to prevent damage. Also the
small diameter of the spacer must point
towards the rod end ball joint.

Z

10. ADJUSTING FOR STRAIGHT FORWARD

TRACKING:

In a large open area, actuate the
Joystick Control lever into the full
forward position. If the mower veers in
either direction left or right some
adjustment is necessary. If the mower
veers to the right, then the right
hydrostat needs to be sped up. If the
mower veers to the left, then the left
hydrostat needs to be sped up.

A.

Stop the machine and shut off the
engine.

B.

Slightly loosen the NUT at the lower end
of the upper linkage assembly on the
side that is slower. Using a 1/8” hex
wrench turn the SETSCREW ¼ turn in.
It may take several test drives to get the
mower to track straight forward.

C.

Once the tracking is to the operators
liking, completely tighten the NUT on the
control linkage assembly that was
loosened earlier.

Spacers (3)
per side

D.

Recheck to make sure neutral adjust
has not been effected

Cross Bolt

Joystick
Pivot Shaft

NUT

SETSCREW

«
...
11
12
13
14
15
...
»

Содержание Jazee




















Отзывы:

Нет отзывов