background image

COTES C30 

OPERATING AND SERVICE HANDBOOK 

  

page 37/48

 

SECTION 7 / CONDENSATION  
OR HEAT RECOVERY UNIT 

RECOMMENDED COMBINATIONS OF DEHUMIDIFIERS AND MODULES 

Using an additional module alongside the dehumidifier unit might affect some of the nominal figures 

provided in the data sheet. Key points are listed below. 

 

The 

HR module

 is not fully compatible with all the dehumidifier units in the range, and it is important 

to realize that the addition of a HR module will affect some of the nominal figures provided in the data 

sheet. This applies particularly to the figures for available external pressure, which will no longer 

apply because some pressure will be lost through the module itself. This loss of external pressure is 

because the airflow must be increased and because the heat exchanger in the module itself adds a 

resistance to the flow of air.  

Note that the energy consumption of a Cotes dehumidifier in BASIC configuration will remain the 

same with a HR module. However, the running time will fall due to the increased capacity when using 

a HR module without modulating heat. 

The 

LK module

 is not fully compatible with all the dehumidifier units in the range. The LK module will 

impact the operating conditions for the dehumidifier. 

 

The following guidelines with regard to compatibility must be respected: 

 

Model 

Compatibility with the LK module 

Compatibility with the HR module 

C30E-0.9 

Fully compatible 

Fully compatible 

C30E-1.2 

Fully compatible 

Fully compatible 

C30E-1.9 

Fully compatible 

Fully compatible 

C30C-0.3 

Not compatible

 

Not compatible 

 

 

 

Содержание C30C

















































Отзывы: