3
English
Use clamps or screw clamps where possible to allow you to handle the work piece with both hands. This is safer
than holding the work piece with one hand.
13. Do not reach too far.
Make sure you always stand firmly and well-balanced.
14. Maintain the tools.
Make sure they are clean and that the blades are sharp to achieve the optimal effect and a safe result. Follow the
recommendations in the manual pertaining to lubricating and replacement of parts. Check the power cord regularly,
and if it is damaged it should be replaced by a qualified service technician. Check all extension cords regularly to
make sure they are not damaged. Make sure the handles of the machine/tool and levers are clean, dry, and com-
pletely free of oil, grease, etc.
15. Turn off the power.
Unplug the device and push the emergency brake, if there is one, before service and when replacing parts such as
planing steel, drills, edges, grinding parts, or blades.
16. Remove all keys and service tools.
Make it a habit to verify that all keys and service tools are removed from the machine before turning on the power.
17. Avoid unintentional start.
Do not carry a tool with your finger on the trigger if it is plugged in. Make sure the trigger is OFF when plugging in the
device.
18. Use the correct extension cords.
If using extension cords outdoors, use only those intended for outdoor use. Use extension cords with sufficient
range, unroll the entire cord.
19. Use common sense and caution.
Think through each task before performing it, so that it is performed in a safe manner. Never use the tool when you
are tired, under the influence of medication, etc.
20. Make sure that all parts are undamaged.
Before starting the tool, make sure that:
•
All covers and additional parts are undamaged and operate correctly.
•
That movable parts can rotate freely and are aimed in the right direction.
•
That no moveable parts can get caught.
•
That no defect has occurred.
•
Other circumstances that may affect the operation of the task.
•
A damaged cover or other part should be repaired by a qualified technician or replaced. Damaged power cords and
power switches must always be replaced by a qualified technician. Never use the tool if you are unable to switch it off
or start it in a safe manner.
21. Use recommended accessories.
The use of not recommended attachments may cause accidents or personal injury.
22. Repair by a qualified technician.
The tool complies with all safety regulations. Repairs of the tool must always be performed by a qualified profes-
sional, using original parts, or the tool may cause accidents or personal injury.
Special safety rules for the Compound Mitre Saw
Caution: Unplug the power cord before service or when replacing a blade.
Make sure that all parts operate properly and that the safety features protect as intended before starting the saw.
1.
Caution
: Use only cutting blades. Make sure that the hard metal blades have negative teeth. Do not use blades with
deep spaces between the teeth as such can bend and come in contact with the blade guard. A damaged saw blade
must be replaced immediately.
2. Do not use the saw until it is completely and accurately assembled according to this operations manual. Verify the
rotation direction of the motor and the blade (see the rotation arrow on the blade guard.) Make certain that the saw
blade does not touch the rotation table in any setting. Unplug the power cord and lean the saw blade manually at 45°
and 90°. Adjust if needed.
3. Unless you understand how the saw is to be used, you should ask a knowledgeable person for advice.
4. Never saw by hand. Fasten the work piece securely against the fence in an appropriate manner before beginning
to saw. If the work piece you are sawing requires that you keep your hand as close as 10 cm from the blade, you
should always lock the work piece in place with a clamp or similar before sawing.
5.
Caution:
Keep your hands clear of the saw blade. Never cut small pieces. Use supports.
6. Make sure that the blade is well centred, sharp, and runs freely without vibrating.
7. Let the motor pick up speed before beginning to saw.
8. Keep the ventilation openings of the motor clean and free of sawdust.
Содержание J1X-JF3-255/07
Страница 43: ...43...
