Cosmo COS-EPGR Скачать руководство пользователя

Страница: 30 / 33

If you are unable to solve an issue even after referring to the

Troubleshooting section of this manual, or if the issue cannot be

fixed, please contact Cosmo Customer Support at:

1-888-784-3108

Problem Probable causes Solution

Some burners will

not light.

Flames do not burn

all around the burner

cap.

Burner parts or igniters may be

wet, dirty or misaligned.

Check that the burner parts are

clean, dry, and correctly assem-

bled. Check that the igniters are

clean and dry. See

"Cleaning instructions", Pages 41-

43.

Burner flames very

large and yellow.

• Burner bezel ports are clogged.

• Burner ports or burner caps are not

positioned properly.

• Cooktop is being operated with the

wrong type of gas.

• Regulator is not installed, is faulty,

or is set for the wrong type of gas.

• Clean burner bezel ring ports with

straightened paper clip,

needle, or wire.

• Remove and carefully re-install

burner bezel and caps.

• Ensure that the type of cooktop

matches the natural gas supply.

• Check installation, replace regulator,

or set regulator for proper gas.

Sparking but no flame

ignition.

Gas shut-off valve is in the

‘OFF’ position.

Turn shut-off valve to the ‘ON’

position.

Igniters spark contin-

uously after flame ig-

nition.

• Power supply polarity is re-

versed.

• Igniters are wet or dirty.

• Have polarity corrected.

• Dry or clean igniters.

Burner flame goes

out at low setting.

• Low gas supply pressure.

• Air intake holes around knobs

are obstructed.

• Contact gas company.

• Remove obstruction.

Troubleshooting Guide - Cooktop

The flames have

suddenly gone out.

A draft or a spill has

extinguished the flame.

No action required. The burner

will detect this and automatically

relight. However, if there has

been a large spill, we

recommend turning the burners

off and cleaning the burners and

sump area. See"Cleaning

instructions", Pages 41-43.

There is a power

failure; can I still use

the cooktop burn-

ers?

Power outage in your area.

The cooktop burners can still be

used. To light them:

1.) Holding a lit match to the

flame spreader, push in the con-

trol knob and turn counter-clock-

wise to LITE.

2.) When the flame is burning all

the way around the burner, you

may adjust the heat.

IMPORTANT!

If the flame is

blown out during a power failure,

turn the knob immediately to

OFF, as the burner will not auto-

matically relight and gas may es-

cape.

Содержание COS-EPGR


































Результаты поиска

Содержание COS-EPGR

Отзывы:

Похожие инструкции для COS-EPGR

Бренды по названию

Популярные бренды

Cosmo COS-EPGR, Руководство пользователя

Результаты поиска

Содержание COS-EPGR

Отзывы:

Похожие инструкции для COS-EPGR

Бренды по названию

Популярные бренды