manualshive.com logo in svg

Cortalk RMU1, Руководство по установке и настройке

Поделиться
Скачать
Cortalk RMU1 Скачать руководство пользователя страница 53

MOBILTEX® DATA LTD. 

Calgary, Alberta 

www.corTalk.com 

TITLE:  

RMU1 Installation and Configuration Guide

 

DOCUMENT NO.: 

RMU1-MAN-001

 

SHEET: 

53 of 53

 

REV: 

1.14 

 

D.

 

RMU1 Regulatory Statements 

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of 
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential 
installation.  This  equipment  generates,  uses  and  can  radiate  radio  frequency  energy,  and  if  not  installed  and  used  in 
accordance  with  the  instructions,  may  cause  harmful  interference  to  radio  communications.  However,  there  is  no 
guarantee that interference will not occur in a particular installation. 

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning 
the equipment OFF and ON, the user is encouraged to try to correct the interference by one or more of the following 
measures: 

• Reorient or relocate the receiving antenna. 

• Increase the separation between the equipment and receiver. 

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 

• Consult the dealer or an experienced radio/TV technician for help. 

WARNING: Changes or modifications not expressly approved by Globalstar may render the device non-compliant to 
FCC and other regulatory body standards for operation and may void the user’s authority to operate the equipment. 

This  device  complies  with  Part  15 of  the  FCC  Rules.  Operation  is  subject  to  the  following  two  conditions:  (1) This 
device  may  not  cause  harmful  interference,  and  (2)  this  device  must  accept  any  interference  received,  including 
interference that may cause undesired operation. 

This ClassA/ClassB digital apparatus complies with Canadian ICES-003. 

NOTICE:  This  equipment  complies  with  the  FCC  RF  Exposure  Limits.  A  minimum  of  20  centimeters  (8  inches) 
separation between the device and the user and all other persons should be maintained. 

 

RMU1-S 
FCC ID: L2V-STX3 
IC:3989A-STX3 

 

RMU1-I 
FCC ID: Q639603N 
IC:4629A-9603N 

 

RMU1-G 
FCCID: RI7LE910NAV2 
IC: 5131A-LE910NAV2 

 

 

Complies with FCC standards. 
FOR HOME OR OFFICE USE 

Содержание RMU1






















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды