CORNING Everon 6000 Скачать руководство пользователя страница 42

Страница: 42 / 75

User Manual v1.0

Corning Restricted and Confidential Proprietary - Controlled content

UM - Everon 6000 DAS - 19-DEC-2020.docx| December 2020

|Page 42 of 170

2.2.6.1

Ground

Note: Ground according to local regulations

The following additional (not supplied) tools and components are required for connecting the system ground:

•

Grounding wire - grounding wire should be sized according to local and national installation

requirements. The provided grounding lug supports 14 AWG to 10 AWG stranded copper (or 12 AWG to
10 AWG solid) wire conductors.

Use a wire-stripping tool to remove approximately 0.4 inch (10.9 mm) of the covering from the end of
the grounding wire

Insert the stripped end of the grounding wire into the open end of the grounding lug

Crimp the grounding wire in the barrel of the grounding lug. Verify that the ground wire is securely
attached to the ground lug by holding the ground lug and gently pulling on the ground wire

Prepare the other end of the grounding wire and connect it to an appropriate grounding point at the site
to ensure adequate earth ground

Содержание Everon 6000












































































Результаты поиска

Содержание Everon 6000

Отзывы:

Похожие инструкции для Everon 6000

Бренды по названию

Популярные бренды

CORNING Everon 6000, Руководство пользователя

Результаты поиска

Содержание Everon 6000

Отзывы:

Похожие инструкции для Everon 6000

Бренды по названию

Популярные бренды