manualshive.com logo in svg

Cornelius VIPER E, Руководство по обслуживанию

Поделиться
Скачать
Cornelius VIPER E Скачать руководство пользователя страница 23

Viper Low overrun Service Manual

© 2016, Cornelius Inc

- 17 -

Publication Number: 621360241LOEWSE

Figure 12. Error Log Screen

Setup Menu

The Setup menu provides the means to change various settings to local preferences, such as time, date and tem-
perature formats. It also allows the user to adjust the unit for the type of syrup being served in each barrel.

To access the Setup menu from the Barrel Status menu, press the MENU button. This displays the Select menu, 
shown in Figure 9. Press the SETUP button to display the Setup menu, shown in Figure 13. To set up the unit 
options, use the Up and Down arrows on the right side of the control panel to highlight the choices on the display. 
When the desired option is highlighted, press the GO button to access that menu.

Figure 13. Setup Screen

Clock Setup Menu

Select the CLOCK SETUP menu from the Select menu, shown in Figure 13. This displays the Clock Setup menu, 
shown in Figure 14. Button functions are described in Table 10.

Table 8.

Button

Description

BACK

Returns the display to the Select menu

Table 9.

Button

Description

BACK

Returns the display to the Select menu

MAIN

Opens the Main menu

SETUP

Highlighted to indicate that the Setup menu is displayed

MAINT

Displays button and opens Maintenance menu, if security is off or 
accessed

GO

Opens the highlighted selection on the current menu

ERROR
LOG

12:51P
MAR 04

ERROR NUMBER    2
#3 COMM FAIL

BACK

OCCUR:           2:44 PM
                          3/04/08
CLEAR:               2:52 PM
                          3/04/08

BACK   MAIN   SETUP   MAINT    GO

SELECT

12:51P
MAR 04

CLOCK SETUP
EVENTS SETUP
VISC SETUP

OPTION SETUP

BACK    MAIN   

 SETUP

  MAINT    

CO2 SETUP

BARREL MAINT

Содержание VIPER E



































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды