background image

Ice Frost Operator’s Manual

Publication Number: M620919596OPR

- 20 -

© 2004-2006, IMI Cornelius Inc.

NOTE 1: the same intervention methods are applied when the safety probe 

is uncovered after the solenoid valve has been activated.

NOTE 2: the 3-second software filter activated when it detects the safety probe is uncovered and the 
relevant signal have been introduced to prevent the probe recognizing the “tank-bowl” conduit as “empty” 
when there is residual gas in it.

Summing Up:

•    When one of the two safety probes fails to detect the passage (presence) of liquid during the fill, the 

system 

will stop

 (3-second software filter) 

the fill cycle in progress

, while the buzzer on the machine 

emits an intermittent warning signal lasting 6 seconds.

•    If the safety probes is uncovered 

when there is no loading phase in progress

 (is de-energized), no 

alarm signal is emitted. 

This signal is activated as soon as the system starts to load the bowl.

If: 

Bowl fill solenoid = ON and Safety probe input = Covered 

 bowl filled as usual

If: 

Bowl fill solenoid = ON and Safety probe input = Uncovered 

 after 3 seconds - Bowl fill 

solenoid = OFF and buzzer is activated

ATTENTION: After the no liquid alarm signal has been activated (safety probe inlet uncovered), 
the actuators for the bowl whose safety probe is uncovered cannot be re-activated. Full 
functioning conditions can only be restored by switching the machine OFF then ON again and re-
starting from the 1st filling phase. When the second safety probe is also identified as uncovered, 
all the charges relating to the system are inhibited (with the exception of CO

2

 gas management 

valve) and the buzzer emits an intermittent sound for approximately 20 seconds. Full functioning 
conditions can only be restored by switching ON and OFF the machine starting from the 1st filling 
phase.

The 

CO

2

 gas management valve

 solenoid valve is independent of the alarm signal and continues 

its 

CO

2

 gas pressure reading function only (see relevant paragraph).

Содержание ICE FROST

































Отзывы: