Cornelius CMP 600-30 Скачать руководство пользователя страница 6

CMP600-30 Icemaker Dispenser Service Manual  

                            

Publication Number: 630460050SER

- 2 -

© 2004-2014, Cornelius Inc.

S

AFETY

 P

RECAUTIONS

This unit has been specifically designed to provide protection against personal injury. To ensure continued protection 
observe the following:

!

WARNING:

Disconnect power to the unit before servicing following all lock out/tag out procedures established by the user. Verify 
all of the power is off to the unit before any work is performed.

Failure to disconnect the power could result in serious injury, death or equipment damage.

CAUTION:

!

Always be sure to keep area around the unit clean and free of clutter. Failure to keep this area clean may result in 
injury or equipment damage.

S

HIPPING

 A

ND

 S

TORAGE

CAUTION:

!

Before shipping, storing, or relocating the unit, the unit must be sanitized and all sanitizing solution must be drained 
from the system. A freezing ambient environment will cause residual sanitizing solution or water remaining inside the 
unit to freeze resulting in damage to internal components.

CAUTION:

!

Very high discharges pressure is present in system. Quick disconnects on your gages will minimize danger and loss 
of refrigerant.

CAUTION:

!

Unit requires separate electrical line. See instruction manual for proper fuse size.

!

WARNING:

There must be adequate clearance around ice maker. Allow minimum 6” air intake and 4” air exhaust for air exhaust 
and panel removal.

NOTE: Unit must be installed per local plumbing and electrical codes. See Installation manual for 
unit requirements. Failure to do so may cause damage to unit, which would void unit warranty.

NOTE: Using any parts other than genuine factory manufactured parts relieves the manufacturer 
of all liability.

NOTE: Manufacturer reserves the right to change specifications at any time.

Содержание CMP 600-30



























Отзывы: