15
P5
P1
P2
JP1
1
1
1
Power Supply
12 or 24 VDC
Black (V-)
Red (V+)
4 – White (GND)
3 – White (TX)
2 – White (RX)
1 – White (+12-15 VDC)
JP1: Place jumper on
Pins 1 & 2 for 12 VDC
and pins 2 & 3 for
24 VDC
24 VDC is Factory Setting
Communication Board
Main Control Board
(V-)
(V+)
Installation and Wiring Instructions for Corbin Russwin WM800
Section 3: Wiring
3.1 Connecting the Communication Board to the Main Control Board
The WM800 is composed of two circuit boards, the control board and the
communication board, which is mounted in the rear keypad housing. The communication
board contains the infrared communications circuitry used for communicating to a PDA
device, as well as the power supply. The power supply circuit should be powered with
12 or 24 VDC. This is selectable by jumper JP1; 24 VDC is the factory setting. For
details, see Figure 9.
The WM800 unit is powered through P2 on the communication board. Connector P1 on
the communication board then provides power to the keypad control board using the
supplied wire harness; this connects to P5 on the control board. The two data wires for
infrared communications are also on this same wire harness. See Figure 9.
Figure 9 Connecting Communication Board to Main Control Board
Branding Guidelines For Installation Instruction Sheets
Endorsed Logo
* Must Be Used On All Single Page and Multiple Page Installation Instruction Sheets
Group Brand Tagline
* Must Be Used On The Bottom Left Of
ALL ONE PAGE
Installation Instruction Sheets
* Must Be Used On The Bottom Left Of
ALL INSIDE
PAGES
of Multiple Page Installation Instruction Sheets
* It is
NOT USED
On The Back Page Or Back Cover Of Installation Instruction Sheets
* Image Must Be Used - CANNOT Be Typed
Corporate Statement
* Must Be Used On The
BACK PAGE
Or
BACK COVER
Of All Multiple Page Installation Instruction Sheets
* Image Must Be Used - CANNOT Be Typed
* A 2 line Version and a 5 Line Version Of The Corporate Statement Image Are Available
Copyright Statement
* Must Be Used On The Bottom of
ALL ONE PAGE
Installation Instruction Sheets
* Must Be Used On The Bottom of The
BACK PAGE
OR
BACK COVER
Of All Multiple Page Installation Instruction Sheets
* Copy Can Be Typed
Copyright © 2008 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.
Note: Marketing will continue to be part of the instruction sheet and template reviewing process
mlw - 07/25/08
Branding Guidelines For Installation Instruction Sheets
Endorsed Logo
* Must Be Used On All Single Page and Multiple Page Installation Instruction Sheets
Group Brand Tagline
* Must Be Used On The Bottom Left Of
ALL ONE PAGE
Installation Instruction Sheets
* Must Be Used On The Bottom Left Of
ALL INSIDE
PAGES
of Multiple Page Installation Instruction Sheets
* It is
NOT USED
On The Back Page Or Back Cover Of Installation Instruction Sheets
* Image Must Be Used - CANNOT Be Typed
Corporate Statement
* Must Be Used On The
BACK PAGE
Or
BACK COVER
Of All Multiple Page Installation Instruction Sheets
* Image Must Be Used - CANNOT Be Typed
* A 2 line Version and a 5 Line Version Of The Corporate Statement Image Are Available
Copyright Statement
* Must Be Used On The Bottom of
ALL ONE PAGE
Installation Instruction Sheets
* Must Be Used On The Bottom of The
BACK PAGE
OR
BACK COVER
Of All Multiple Page Installation Instruction Sheets
* Copy Can Be Typed
Copyright © 2008 Corbin Russwin, Inc., an ASSA ABLOY Group company. All rights reserved.
Reproduction in whole or in part without the express written permission of Corbin Russwin, Inc. is prohibited.
Note: Marketing will continue to be part of the instruction sheet and template reviewing process
mlw - 07/25/08
