background image

4

SRSH IO&M

B51142-004

An NLGI #2 grease is a light viscosity, low-torque, rust-in-

hibiting lubricant that is water resistant. Its temperature range 

is  from  -30°F  to  200°F  and  capable  of  intermittent  highs  of 

250°F. 

Bearings should be prelubricated in accordance with the fol

-

lowing conditions chart.

Conditions Chart

RPM

Temp °F

Greasing Interval

Up to 1000

-30 to 120

3 months

120 to 200

1 month

1000 to 3000

-30 to 120

6 weeks

120 to 200

2 weeks

Over 3000

-30 to 120

2 weeks

120 to 200

1 week

Any Speed

< -30

Consult Factory

Any Speed

> 200

1/2 week

For moist or otherwise contaminated installations, divide the interval 

by a factor of three.

For best results, lubricate the bearing while the fan is in 

operation. Pump grease in slowly until a slight bead forms 

around the bearing seals. Excessive grease can damage the 

seal and reduce the life through excess contamination and/or 

loss of lubricant.

In the event that the bearing cannot be seen, use no more 

than three injections with a hand operated grease gun.

Lubricants

Loren Cook Company uses petroleum lubricant in a lithium 

base conforming to NLGI grade 2 consistency. Other grades 

of grease should not be used unless the bearings and lines 

have been flushed clean. If another grade of grease is used, it 

should be lithium-based. 

An  NLGI  grade  2  grease  is  a  light  viscosity,  low-torque, 

rust-inhibiting  lubricant  that  is  water  resistant.  Its  tempera-

ture range is from -30°F to +200°F and capable of intermittent 

highs of +250° F.

Motor Bearings

Motors are provided with prelubricated bearings. Any lubri

-

cation instructions shown on the motor nameplate supersede 

the following instructions.

Direct Drive 1050/1075, 1200, 1300 & 1500 RPM units use 

a prelubricated sleeve bearing that has a oil saturated wicking 

material surrounding it. The initial factory lubrication is ade

-

quate for up to 10 years of operation under normal conditions. 

However, it is advisable to add lubricant after 3 years. Use 

only LIGHT grade mineral oil or SAE 10W oil up to 30 drops. 

If the unit has been stored for a year or more it is advisable to 

lubricate as directed above. 

Motors without sleeve bearings (as described above) will 

have grease lubricated ball or roller bearings. Motor bearings 

without provisions for relubrication will operate up to 10 years 

under normal conditions with no maintenance. In severe ap

-

plications, high temperatures or excessive contaminates, it is 

advisable to have the maintenance department disassemble 

and lubricate the bearings after three years of operation to 

prevent interruption of service.

For motors with provisions for relubrication, follow intervals 

of the table below.

Relubrication Intervals

Service 

Conditions

Nema Frame Size

Up to and 

Including 184T

213T-365T

404T and Larger

1800 

RPM & 

Less

Over 

1800 

RPM

1800 

RPM & 

Less

Over 

1800 

RPM

1800 

RPM & 

Less

Over 

1800 

RPM

Standard

1-1/2 yrs.

3 mos.

1 yr.

3 mos.

6 mos.

6 wks.

Service

6 mos.

6 wks.

6 mos.

6 wks.

3 mos.

2 wks.

For units in severe conditions, lubrication intervals should be re

-

duced to half.

Motors are provided with a polyurea mineral oil NGLI #2 

grease. All additions to the motor bearings are to be with 

a compatible grease such as Exxon Mobil Polyrex EM and 

Chevron SRI.

Motor Services

Should the motor prove defective within a one-year period, 

contact your local Loren Cook representative or your nearest 

authorized electric motor service representative.

Changing Shaft Speed

All belt driven ventilators (5HP or less) are equipped with 

variable pitch pulleys. To change fan speed, perform the fol

-

lowing:

1.  Loosen setscrew on driver (motor) pulley and remove key, 

if equipped.

2.  Turn the pulley rim to open or close the groove facing. If 

the pulley has multiple grooves, all must be adjusted to 

the same width.

3.  After adjustment, inspect for proper belt tension.

Speed Reduction

Open the pulley in order that the belt rides deeper in the 

groove (smaller pitch diameter).

Speed Increase

Close the pulley in order that the belt rides higher in the 

groove (larger pitch diameter). Ensure that the RPM limits of 

the fan and the horsepower limits of the motor are maintained.

Maximum RPM

SRSH 

Size

Maximum 

RPM

60-100

2125

120

1715

135

1620

150

1550

165

1325

180

1535

195

1370

210

1210

225

1060

245

900

270

765

Содержание SRSH-B









Отзывы: