Contura C 660K Скачать руководство пользователя страница 2

66

GB

CERTIFICATE

PRODUCT

Product type 

Stove lit with solid biofuels 

Type designation 

Contura 660K 

Manufacturing number 

See rating plate on the stove 

Intended area of use 

Heating of rooms in residential buildings 

Fuel 

Wood

MANUFACTURER

Name 

NIBE AB / Contura 

Address 

Box 134, Skulptörvägen 10 

 

SE-285 23 Markaryd, Sweden

CHECKS

According to AVCP 

System 3 

European standard 

EN 13240:2001 / A2:2004   

Test institute 

Rein-Ruhr Feuerstätten Prüfstelle, NB 1625,

 

has checked declared performance and issued test report no. RRF-40 07 1478   

PERFORMANCE DECLARATION

No. C660K-CPR-130608-SE-1

DECLARED PERFORMANCE

Essential characteristics

Performance

Harmonised technical
specification

Reaction to fire

A1 WT

Minimum distance to combustible material

100 mm to rear
500 mm to side  
Other safety distances according to 
the installation instructions

Risk of falling embers

Approved

Emissions from combustion

CO           0.06% 
NOx         115 mg/m

3

 

OGC         57 mg/m

3

 

PM           28 mg/m

3

Surface temperatures

Approved

Cleaning options

Approved

Mechanical durability

Approved

Emissions of hazardous substances

Approved

Nominal output

6 kW

Efficiency

79%

Flue gas temperature in connector at nominal 
output

280°C

EN 13240:2001 / A2:2004

The undersigned is responsible for the manufacture and conformity with the declared performance.

Niklas Gunnarsson,

 

Business area manager NIBE STOVES

 

Markaryd, 1st July 2013

Содержание C 660K

















Отзывы: