background image

X-18s™ Users Manual

Appendix D: FCC Statement

Appendix D: FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference.

This device must accept any interference received, including interference that may cause undesired 

operation.

Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection. This 
equipment generates, uses and can radiate radio frequency energy and, if not installed and used in 
accordance with the instructions, may cause interference to radio communications. There is no 
guarantee, however, that interference will not occur in a particular installation. If this equipment does 
cause harmful interference to radio or television reception, which can be determined by turning the 
equipment off and on, the user is encouraged to try to correct the interference by one or more of the 
following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment to a circuit different from where the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

Notice

Changes or modification not expressly approved by the party responsible for compliance could void the 
user’s authority to operate the equipment.

Xytronix Research & Design, Inc.

Page 17

Содержание X-18s



















Отзывы: