manualshive.com logo in svg

Control Techniques MD29, Руководство по установке

Поделиться
Скачать
Control Techniques MD29 Скачать руководство пользователя страница 13

UD70/MD29 Installation Guide

10

Issue Number: 3

www.controltechniques.com

3.2

Data Rate

Unidrive:

#17.07

Mentor II:

#14.03

Range:

300 to 38400 bits per second

Default:

4800

Every node on an ANSI or Modbus network must be configured to operate at the
same data rate. Set the appropraite value as shown in the table below to configure
the RS485 port data rate.

3.3

RS485 Port Communications Modes

Unidrive:

#17.06

Mentor II:

#14.02

The serial communications mode selector determines the mode of operation of the
RS485 serial port, and the protocol supported. Only slave modes are described
here. (Modes 6 to 9, 11 and 12 require DPL code to control the RS485.)

3.3.1

Standard CT ANSI Protocol

Mode 1 - 4 Wire ANSI Slave Mode (Default)

Mode 5 - 2 Wire ANSI Slave Mode

The UD70 and MD29 will communicate using the Control Techniques' standard
ANSI protocol with a 4-wire or 2-wire connection. This mode allows the Unidrive or
Mentor II to communicate with standard CT software packages, such as UniSoft,
MentorSoft, SystemWise, etc.

Menu 0 parameters are not accessible through a UD70 or MD29. Refer to the
User's Guide for MD29 or UD70 for a detailed description of the ANSI protocol.

3.3.2

Modbus RTU

Mode 13 - 4 Wire Modbus RTU Slave Mode

Mode 15 - 2 Wire Modbus RTU Slave Mode

The UD70 and MD29 will communicate using the Modicon Modbus RTU protocol
with a 4-wire or 2-wire connection. The data frame used for Modbus RTU is 1 start
bit, 8 data bits, no parity, 2 stop bits. (Even parity with 1 stop bit is NOT currently
supported.)

The following MOdbus RTU commands are supported:

FC3

PRESET SINGLE REGISTER

FC6

PRESET MULTIPLE REGISTERS

FC16

READ MULTIPLE REGISTERS

The maximum number of registers that can be transferred on a single message is
limited to 20, and the range of allowed node addresses is limited from 1 to 99.

Data Rate

(bits/sec)

Unidrive

Mentor II

300

300

3

600

600

6

1200

1200

12

2400

2400

24

4800

4800

48

9600

9600

96

19200

19200

192

38400

38400

38

Содержание MD29
















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды