Troubleshooting
If light does not turn on:
•
Ensure at least one LED on the face of the switch is lit.
•
Ensure the light bulb is not burned out and is screwed in tightly.
•
Ensure circuit breaker is not turned OFF or tripped.
•
Check for proper wiring (see the “”section).
•
For help on the installation or operation of this product, email or call the Control4
Technical Support Center. Please provide your exact model number. Contact
[email protected] or see the web site www.control4.com.
Operation and Configuration
On initial power up, the unit
will flash the Red/Green/
Blue (RGB) LEDs, which
can be programmed with
different colors for different
states or color preferences.
To set up this switch for use
with a Control4 system,
refer to your system setup
documentation.
To operate this switch as a stand-alone device, refer to the following tables.
Limited 2 Year Warranty
Control4 Corporation ("Control4") warrants that at the time of first-consumer sale, this
product will be free from defects in material and manufacture. Control4 further warrants
that for a period of 2 years (24 months) after initial consumer sale, the product will function
in accordance with its specification, provided that it is installed and maintained under
normal and proper use. This warranty extends only to products purchased directly from
Control4 or an Authorized Control4 Reseller. If the product proves to be defective in
material or workmanship during the warranty period, it may be returned to the place of
purchase and Control4 will, at its sole option, repair or replace the product with a like
product. This warranty provides the consumer purchaser with specific legal rights, which
may vary per state or country. For complete warranty information, including details on
consumer legal rights as well as warranty exclusions, visit www.control4.com/warranty.
Regulatory Compliance
FCC
FCC ID: R33C4SW1Z
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT!
Any changes or modifications not expressly approved by the
party responsible for compliance could void the user’s authority to operate this
equipment.
ETL Statement
ETL Control Number: 3129831
This product has been tested by ETL and was found to comply with the Standard for
Safety for Industrial Control Equipment:
•
UL/ANSI Standard 508 (Seventeenth Edition)
•
CSA Standard C22.2 No. 14-05
Industry Canada
IC ID: 7848A-C4SW1Z
This Class B digital apparatus complies with Canada ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Protected under U.S. Patents 7,106,261 and licensed under U.S. Patents 5,905,442 and
5,982,103
About this Document
United States Patents Pending. ©2009 Control4. All rights reserved. Control4, the Control4
logo and Everyday Easy are registered trademarks or trademarks of Control4 Corporation
in the United States and/or other countries. All other names or brands may be claimed as
property by their respective owners. Pricing and specifications subject to change without
notice. Part Number: 200-00036 Rev D
Operate Switch
Expected behavior of RGB LEDs:
To operate switch:
Top
Bottom
Turn ON: Tap top.
Lit, full brightness
Not lit
Turn OFF: Tap bottom.
Not lit
Lit, full brightness
Care and Cleaning
Do NOT paint switch or its wall plate.
Do NOT use any chemical cleaners to clean the switch.
Clean surface with a soft damp cloth as needed.
