background image

Warnings and considerations

WARNING! 

Turn OFF electrical power before installing or servicing this 

product. Improper use or installation can cause SERIOUS INJURY, DEATH 

or LOSS/DAMAGE OF PROPERTY.

ATTENTION!

 Coupez l’alimentation électrique avant d’installer ou de 

réparer ce produit. Une mauvaise installation ou utilisation peut entraîner 

des blessures graves, décès ou perte / dommages à la propriété.

WARNING! 

This device must be protected by a circuit breaker (20A max).

ATTENTION!

 Cet appareil doit être protégé par un disjoncteur (20A max.)

WARNING! 

Ground this device in accordance with the National Electric 

Code (NEC) requirements. DO NOT rely solely upon the yoke plate’s 

contact with a metal back box for adequate grounding. Use the device’s 

ground wire to make a secure connection to the safety ground of the 

electrical system.

ATTENTION! 

Cet appareil doit être en conformité avec le Code national de 

l’électricité (NEC). Ne comptez pas uniquement au contact de la plaque 

avant avec un boîtier mural métallique pour la mise à la terre adéquate. 

Utilisez cet appareil à la terre de l’appareil pour établir une connexion 

sécurisée au système électrique.

IMPORTANT! 

This device must be installed by a licensed electrician in 

accordance with all national and local electrical codes.

IMPORTANT! 

If you are unsure about any part of these instructions, 

consult a qualified electrician.

IMPORTANT! 

Use this device only with copper or copper-clad wire. Do 

not use aluminum wiring. This product has not been approved for use with 

aluminum wiring.

IMPORTANT! 

Using this product in a manner other than outlined in this 

document voids your warranty. Further, Control4 is NOT liable for any 

damage incurred with the misuse of this product. See “Troubleshooting.”

IMPORTANT! 

Do NOT use a power screwdriver to install this device. If you 

do, you may overtighten the screws and strip them. Also, overtightening 

the screws may interfere with proper button operation.

IMPORTANT! 

This is an electronic device with intricate components. 

Handle and install with care!

IMPORTANT! 

This device must not be connected to a bathroom exhaust 

fan. This type of motor is not compatible.

IMPORTANT! 

When used in conjunction with an Auxiliary Keypad 

(C4-KA-xx), the wire connecting the Auxiliary Keypad to the Fan Speed 

Controller must not exceed 150 feet (45 m) at 120VAC, and 100 feet (30 

m) at 277VAC.

Installation instructions

Ensure that the location and intended use meet the following criteria:

• 

If the ceiling fan being controlled is a fan/light combination, there must 

be separate load wires for the fan and light from the control location. A 

separate Control4 dimmer or switch must be used if the light is to be 

controlled. Do not use the Fan Speed Controller to control the light.

• 

Do not exceed the load capacity requirements of the Fan Speed 

Controller. Refer to the load ratings in the specifications above for details.

• 

Install in accordance with all national and local electrical codes.

• 

The range and performance of the wireless control system is highly 

dependent on the following: (1) distance between devices; (2) layout 

of the home; (3) walls separating devices; and (4) electrical equipment 

located near devices.

Supported model

• 

C4-4SF120 Fan Speed Controller

Introduction

The Control4® Fan Speed Controller operates independently or as part of a 

Control4 home automation system to provide four quiet speeds plus an Off 

setting for standard paddle-type ceiling fans. It installs in a standard back box 

using typical wiring standards and communicates to the Control4 system using a 

wireless connection.

Box contents

• 

Fan Speed Controller

• Wire 

nuts

• Warranty 

card

•  Fan Speed Controller Installation Guide

 (this document)

Specifications and supported load types

The specifications are described below.

Model number

C4-4SF120-xx

Power requirements

120V AC +/-10%, 50/60 Hz

This device requires a neutral connection. See 
the “Sample Wiring Configurations” later in this 
guide.

Power consumption

500mW

Load types and ratings

Supported load types

Single, paddle-type ceiling fan

Maximum load

2A

Environmental

Operational temperature

0 to 40 ˚C (32 to 104 ˚F)

Humidity

5% to 95% non-condensing

Storage

-20 to 70 ˚C (-4 to 158 ˚F)

Miscellaneous

Control communications

Zigbee, IEEE 802.15.4, 2.4 GHz, 15-channel 
spread spectrum radio

Wallbox volume

5.75 cubic inches

Weight

0.05 kg (0.12 lb.)

Shipping weight

0.08 kg (0.18 lb.)

Fan Speed Controller 

Installation Guide

Отзывы: