2
Turn off the local electrical power by either switching off the circuit breaker or
removing the fuse from the fuse box. To ensure the wires do NOT have power
running to them, use an inductive voltage detector.
NOTE:
The back box wiring shown in this document is an example. Your
wire colors and functions may differ. If you are not sure which wires are
the Line In/Hot, Neutral, Load, Traveler, and Earth Ground wires, have a
trained electrician perform the installation.
3
Prepare each wire. Wire insulation should be stripped back 16 mm (5/8 in.)
from the wire end (see Figure 1).
Figure 1.
Strip wire insulation
4
Identify your wiring application, and then see the appropriate wiring diagram
in the “Sample Wiring Configurations” section below.
IMPORTANT!
Not grounding this product, as described in the section
“Warnings and Considerations,” may result in an installation less immune
to damage caused by electrical disturbances, such as ESD or lightning,
and may void the warranty.
5
Identify and connect the Fan Speed Controller wires to the back box wires
using the wire nuts.
IMPORTANT!
The yellow wire is not a traditional traveler. It cannot directly
power a load. It must be used only to connect to a Control4 Auxiliary
Keypad. See “Sample Wiring Configurations.”
TIP:
If you are using a Control4 push-on (screwless) faceplate in a multi-
gang installation, attach the black faceplate sub-plate to all of the devices
that will be installed into the wallbox prior to attaching the devices to the
wallbox. This will help ensure that all the devices are properly aligned and
on the same plane after installation.
6
Fit the wires back into the back box. Bend the wires in a zigzag pattern so
that they easily fold into the back box (Figure 2).
Figure 2.
Bend the wires
7
Align the Fan Speed Controller to the back box (the load rating label should
be at the bottom) and fasten it with screws. Tighten the screws until the
back side of the yoke plate is even with the wall surface, but no further.
Overtightening can warp the dimmer and cause mechanical malfunction.
8
Install the Control4 Faceplate following the instructions in the
Faceplate
Installation Guide
or attach a standard Decora-style faceplate.
9
Turn ON power at the circuit breaker or replace the fuse
from the fuse box.
Operation and configuration
On initial power up, all status LEDs on the Fan Speed Controller will illuminate
green indicating that the device has power. To set up the Fan Speed Controller for
use with a Control4 system, refer to the
Composer Pro User Guide
.
IMPORTANT!
If the fan speed can be adjusted via a pull chain, remote
control, etc., set the fan to high speed using that method prior to
operating with the Control4 Fan Speed Controller.
To operate the Fan Speed Controller as a stand-alone device:
• Click
the
top
button to turn the fan on at high speed.
• Click
the
second
button to turn the fan on at medium-high speed.
• Click
the
third
button to turn the fan on at medium speed.
• Click
the
fourth
button to turn the fan on at low speed.
• Click
the
bottom
button to turn the fan off.
Button tap sequences
The button tap sequences are defined in the table below. Button tap sequences
that require a single button should use the top button.
Function
Button sequence
Identify
4
Zigbee channel
7
Reboot
15
Factory reset
9-4-9
Leave mesh and reset
13-4-13
Troubleshooting
If the fan does not turn on:
•
Ensure at least one LED on the face of the Fan Speed Controller is lit.
•
Ensure the light bulb is not burned out and is screwed in tightly.
•
Ensure that the circuit breaker is not turned OFF or tripped.
•
Check for proper wiring (see “Sample Wiring Configurations”).
•
For help on the installation or operation of this product, email or call the
Control4 Technical Support Center. Please provide your exact model number.
Contact
or see the web site
www.control4.com
.
Care and cleaning
•
Do NOT paint the Fan Speed Controller or its wall plate.
•
Do NOT use any chemical cleaners to clean the Fan Speed Controller.
•
Clean surface of the Fan Speed Controller with a soft damp cloth as needed.
Warranty and legal notices
Find details of the product’s Limited Warranty at
snapav.com/warranty
or request
a paper copy from Customer Service at
866.424.4489
. Find other legal resources,
such as regulatory notices and patent information, at
snapav.com/legal
.
