Contrinex YRB-4EML-31S Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 36

background image

Application manual for YRB-4EML-31S safety relay

Contrinex AG Industrial Electronics

3

Please observe the following notes

User group of this manual

The use of products described in this manual is oriented exclusively to:
– Qualified electricians or persons instructed by them, who are familiar with applicable

standards and other regulations regarding electrical engineering and, in particular, the
relevant safety concepts.

– Qualified application programmers and software engineers, who are familiar with the

safety concepts of automation technology and applicable standards.

Explanation of symbols used and signal words

This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety measures that follow this symbol to avoid possible
injury or death.

There are three different categories of personal injury that are indicated with a
signal word.

DANGER

This indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

This indicates a hazardous situation which, if not avoided, could
result in death or serious injury.

CAUTION

This indicates a hazardous situation which, if not avoided, could

result in minor or moderate injury.

This symbol together with the signal word

NOTE

and the accompanying text

alert the reader to a situation which may cause damage or malfunction to the
device, hardware/software, or surrounding property.

This symbol and the accompanying text provide the reader with additional
information or refer to detailed sources of information.

How to contact us

Internet

Up-to-date information on Contrinex products and our Terms and Conditions can be found
on the Internet at:

www.contrinex.com

Subsidiaries

If there are any problems that cannot be solved using the documentation, please contact
your Contrinex subsidiary.
Subsidiary contact information is available at

www.contrinex.com

.

Published by

CONTRINEX SA

André-Piller 50
1762 Givisiez
SWITZERLAND

Should you have any suggestions or recommendations for improvement of the contents and
layout of our manuals, please send your comments to:

[email protected]

«
1
2
3
4
5
...
»

Содержание YRB-4EML-31S





































Отзывы:

Нет отзывов

Похожие инструкции для YRB-4EML-31S

Бренд: RIESE Страницы: 9

Бренд: Pilz Страницы: 14

Бренд: National Instruments Страницы: 51

System pro M RHI

Бренд: ABB Страницы: 50

Бренд: ABB Страницы: 52

Бренд: ABB Страницы: 22

Бренд: ABB Страницы: 68

Бренд: ABB Страницы: 7

Бренд: ABB Страницы: 72

Бренд: ABB Страницы: 2

Бренд: ABB Страницы: 3

Бренд: ABB Страницы: 100

Бренд: ABB Страницы: 60

Бренд: ABB Страницы: 38

Бренд: ABB Страницы: 20

Бренд: ABB Страницы: 72

Бренд: ABB Страницы: 16

Бренд: ABB Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды