Congratulations on purchasing your new CW
®
O a k
Fantasy
®
Vanity Flair. Now that you have opened the
package, we want you to verify that you have all the
necessary hardware supplied with your doors.
PARTS CHECK LIST:
N
O
.
Q
TY
D
ESCRIPTION
(#1)
3
Mirrored Glass Panels
(#2)
2
Magnetic Oak Catch
Installed in Panel
(#3)
2
Strike Washer
(#4)
2
#6 x 1/2
″
Screws
(#5)
2
Masonite
(#6)
4
Pivot Hinges
(#7) 24
#8 x 1/2
″
Truss Screws
(#8)
2
Brackets
(#9)
8
#6 x 3/8
″
Screws
(#10) 2
Anchors
(#11) 8
#8 x 1-1/2
″
PH SMS Screws
If you find that any parts are damaged or missing, refer to
the parts list and IPB Drawing and contact
Contractors Wardrobe
®
’s Customer Service Department
at (661) 257-1177.
TOOL CHECK LIST
You will need:
• Phillips Screwdriver
• Tape Measure
• Hammer
• Pencil
• 3/8
″
Drill Motor and 3/16
″
and 1/8
″
Drill Bits
• Square or Level
Oak Fantasy
®
Vanity Flair - 0309
STEP 2
Mounting the Vanity Flair
Place the Mirrored Glass Panels (#1) against
the wall where you want to install it. Open the
left wing and mark the wall through all the holes
in the Bracket (#8). Next, open the right wing
and mark the wall through all the holes in the
Bracket (#8). Next, move the Mirrored Glass
Panels (#1) out of the way. Carefully drill a 1/8
″
hole in the wall where you marked the holes
through the Bracket (#8). If you did not drill into
a wooden stud, you will need to use wall
anchors. After you drill all of the holes and
install the anchors, if necessary, move the
Mirrored Glass Panels (#1) back into place.
Next, insert the #8 x 1-1/2
″
PH SMS Screws
(#11) through the holes in each Bracket (#8).
STEP 3
Installing the Strike Washer
Place #6 x 1/2
″
Screw (#4) inside the Strike
Washer (#3) and place onto Magnetic Oak
Catch (#2). Close door with screw facing wall.
This will mark where your #6 x 1/2
″
Screw (#4)
and Strike Washer (#3) will go. Open wing and
remove from Magnetic Oak Catch (#2). Install
#6 x 1/2
″
Screw (#4) and Strike Washer (#3)
where your mark is on the wall. Repeat this step
for the second wing. Your Oak Fantasy
®
Va n i t y
Flair is complete.
I N S TALLING THE OAK FA N TA SY
®
VANITY FLAIR
STEP 1
Measure for Center of Opening
Place Mirrored Glass Panels (#1) onto back
splash. Using Tape Measure, measure left and
right sides to find center of opening (You may
need a second person to help hold the Mirrored
Glass Panels (#1) in place, while measuring the
opening to find the center).
Thank you for purchasing a CW
®
Wardrobe Door. This
is only part of a large line of wardrobe doors and high
quality bath enclosure products. If you like this product,
please contact Contractors Wa r d r o b e
®
for more
information about our many beautiful bath enclosures
available in a vast array of colors and finishes to suit
your designing needs.
2
Oak Fantasy Vanity Flair 0209 3/5/09 2:39 PM Page 2
