26
27
Contractions
are weak even
though the
intensity is high
The batteries are low.
Replace all 4 AAA batteries.
Never mix old and new bat-
teries.
IMPORTANT: NEVER
REPLACE BATTERIES
WHILE THE DEVICE IS ON
The gel pads have lost
conductivity.
Replace gel pads.
The pads are not
positioned properly.
Turn the device off, remove
the Muscle Stimulator Ab
Belt and reposition as
described in this manual.
Make sure the gel pads are
below your rib cage.
Stimulation is
uncomfortable
The gel pads may be
worn out.
Replace gel pads.
Intensity level might be
set too high.
Reduce the intensity level
until your body gets used
to it.
The gel pads are not
positioned properly.
Turn the device off, remove
the Muscle Stimulator Ab
Belt and reposition as de-
scribed in this manual. Make
sure the gel pads are below
your rib cage.
Too many sessions in
a row.
Leave at least six hours
between sessions.
My muscles are
sore after using
the Ab Belt
Intensity level might be
set too high.
Reduce the intensity level.
I feel tingling in
my legs
Gel pads are located
near a nerve center.
Turn the device off and move
the gel pads slightly.
I’m not
seeing results
Your diet plays a vital
role.
Follow a reduced calorie
eating plan and get some
regular exercise.
The intensity level
might not be set high
enough to get good
contractions.
Increase the intensity level.
MUSCLE STIMULATOR DEVICE CHARACTERISTICS
Device Name: Muscle Stimulator, MX9
Waveforms: The waveform is monophasic rectangular, voltage regulated.
Parameters: The parameters (pulse rate, pulse duration, stimulation time,
rest time) are optimized for each program.
Pulse Duration: Maximal impulse duration is 340 µs
Protection against electric shock: Internal electrical power source
Maximum Output: 40.9 Volts ± 10%
DC Component:
2 Volts ± 10%
Channels:
2 independent, isolated channels
Separate Intensity control levels for each channel
Power Supply:
4 AAA battery 1.5 V (Alkaline)
Approx. max consumption:
130 mA at 100% intensity
Approx. normal consumption: 40 mA at 100% intensity
Battery Life: 20 hours at 100% intensity
Pulse Frequency Range:
1 – 120 Hz
Impedance
Range:
500-2.5k
Ohms
FDA Clearance: Nonprescription, over-the-counter use.
The device is manufactured in accordance with the requirements of
International Standards IEC 60601-1, IEC 60601-2-10. The device conforms
to requirements of the United States Food and Drug Administration (FDA) for
non-prescription
sales.
Environmental Specs: Operating Temperature Range: 10 - 40°C (50 - 104°F)
Operating Humidity: 30 - 75 % RH
Storage and Transit Temperature Range: -29 - 60°C
(-20
-
140°F)
Storage and Transit Humidity: 20 - 85 % RH
MUSCLE STIMULATOR AB BELT CHARACTERISTICS
Inner material: 85% Nylon
15% Polyester
Elastic Fabric: 100% Neoprene
Outer Material: 60% Polyester
40% Nylon
Other Fabrics: 100% Polyester
This symbol means "Serial
number"
The supplied
documentation
must be consulted
for operating,
cautionary or safety information
before using the device.
Muscle Stimulator is a class II
device unit with its own internal
electric power, with type BF
applied sections. The outputs are
isolated from other parts of the device
that provide a protection against
electrical shock.
This symbol means please apply
regulations enforced in your country
when disposing your batteries and
product at its end of life Ensuring it
is disposed in an environmentally
friendly manner.
Description of symbols : There are a number of technical symbols on your ems device explained as follows:
