Contec HPC-HLS10 Series Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 39

background image

1. Introduction

IPC-PT/MV10 / IPC-PT/LS10 / HPC-HMV10 / HPC-HLS10 Hardware Manual

5

FCC PART 15 Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful

interference at his own expense.

NOTE

Change or modifications not expressly approved the manufacturer can void the user's authority to

operate this equipment.

WARNING TO USER

«
...
8
9
10
11
12
...
»

Содержание HPC-HLS10 Series








































Отзывы:

Нет отзывов

Похожие инструкции для HPC-HLS10 Series

Бренд: IBASE Technology Страницы: 60

Бренд: PowerWave Страницы: 16

AFOLUX 915A Series

Бренд: IEI Technology Страницы: 155

Бренд: Advantech Страницы: 80

Бренд: Sunforce Страницы: 1

Бренд: BMS energy Страницы: 40

Бренд: ICP Electronics Страницы: 7

Бренд: Yalp Страницы: 68

Бренд: Insignia Страницы: 91

auroTHERM VFK 900

Бренд: Vaillant Страницы: 69

VICPAS C70 Series

Бренд: B&R Страницы: 108

Бренд: IBASE Technology Страницы: 78

Бренд: Aaeon Страницы: 29

Бренд: Icop Страницы: 29

Бренд: Velux Страницы: 24

LC42D65U - LC - 42" LCD TV

Бренд: Sharp Страницы: 114

Бренд: Sharp Страницы: 56

Бренд: Sharp Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды