Contec CPS-PCS341EC-DS1-1201 Скачать руководство пользователя

Страница: 31 / 44

3 Nomenclature and Functions

CPS-PCS341EC-DS1-1201 Hardware Manual

LED Indicator

Table 3.2. LED indicator-1

LED

Operation

Meaning

PWR(Green)

Power has been supplied.

OFF

Power has not been supplied.

ST1(Green)

Refer to the software manual, CPS-PC Series system setup guide.

ST2(Red)

Refer to the software manual, CPS-PC Series system setup guide.

ERR(Red)

It will light up when the error occurs.

OFF

It indicates the system runs normally.

DIO0-DIO3(Green)

It will light up at the time of inputting/outputting.

OFF

It indicates there is no inputting/outputting.

Table 3.3. LED indicator-2

LED

Operation

Meaning

SD(Green)

Flashing

It will flash at the time of SD access.

OFF

It indicates there is no SD access.

COM -TX(Green)

Flashing

It will flash when sending data by the RS-232C.

OFF

It indicates no data sending by the RS-232C.

COM -RX(Green)

Flashing

It will flash when receiving data by the RS-232C.

OFF

It indicates no data receiving by the RS-232C.

PWR ST1 ST2 ERR

DIO

Содержание CPS-PCS341EC-DS1-1201













































Результаты поиска

Содержание CPS-PCS341EC-DS1-1201

Отзывы:

Похожие инструкции для CPS-PCS341EC-DS1-1201

Бренды по названию

Популярные бренды

Contec CPS-PCS341EC-DS1-1201, Руководство по оборудованию

Результаты поиска

Содержание CPS-PCS341EC-DS1-1201

Отзывы:

Похожие инструкции для CPS-PCS341EC-DS1-1201

Бренды по названию

Популярные бренды