Contec CONPROSYS CPS-MC341-DS1-111 страница 51 Скачать руководство пользователя

Страница: 51 / 71

—

Installation

—

CPS-MC341-DS1-111 Reference Manual (Hardware)

—

Connecting to an external device

Connect the product in accordance with the specification of the external device.



Notes on the Shield Connection



Ground the shield to the frame ground (FG) of the external device.



Use an unshielded cable if there is no terminal or/and place for grounding.



Do not ground to Power GND.



Shield should not be used as the signal ground (SG).

CAUTION



Tightening torque of the supplied connector is described below.
DEGSON : 0.19 N·m, PHOENIX CONTACT, PTR MESSTECHNIK : 0.25 N·m



Strip off approximately 7mm (plus or minus 0.5mm) of the covered part of a cable to connect
with the connector.



If the shielded cables are incorrectly wire-connected to the ground, the shield might become
an antenna picking up noises or become a source of noise.



If you find the problems, remove the grounding of the shield.



About a caution mark on the product: Please use copper wires that withstand the temperature
of 75 °C and higher.

TX+

TX－

RX+

RX－

TX+

TX－

RX+

RX－

RS-422A/485

5-pin connector

External device

Содержание CONPROSYS CPS-MC341-DS1-111








































































Результаты поиска

Содержание CONPROSYS CPS-MC341-DS1-111

Отзывы:

Похожие инструкции для CONPROSYS CPS-MC341-DS1-111

Бренды по названию

Популярные бренды

Contec CONPROSYS CPS-MC341-DS1-111, Справочное руководство

Результаты поиска

Содержание CONPROSYS CPS-MC341-DS1-111

Отзывы:

Похожие инструкции для CONPROSYS CPS-MC341-DS1-111

Бренды по названию

Популярные бренды