Ver.1.05
AIO-160802LI-PE
4
The following figure shows an example of shield cable connection. Use
shielded cable if the distance between the signal source and board is
long or if you want to provide better protection from noise. For each
analog input channel on CN1, connect the core wire to the signal line
and connect the shielding to ground.
Analog Output Connection (Shield Cable)
*2 The number of channels depends on each board. The AIO-160802LI-PE has two channels.
CAUTION
-
When the power supply is turned on, the output voltage of all channels becomes 0V.
-
If the board or the connected wire receives noise, or the distance between the board and the
target is long, data may not be outputted properly.
-
Do not short the analog output signal to analog ground, digital ground, and/or power line.
Doing so may damage the board.
-
Do not connect an analog output signal to any other analog output, either on the board or on
an external device, as this may cause a fault on the board.
-
Analog ground of CN1 is isolated from the ground in the PC.
Digital I/O signals, Counter signals and Control
signals Connection
The following sections show examples of how to connect digital I/O
signals, counter I/O signals, and other control I/O signals (external
trigger input signals, sampling clock input signals, etc.).
All the digital I/O signals and control signals are TTL level signals.
Digital Input Connection
Digital Output Connection
About the counter input control signal
Counter Gate Control Input (refer to the chapter 3 Connector Pin
Assignment) acts as an input that validate or invalidate the input of an
external clock for the counter. This function enables the control of an
external clock input for the counter. The external clock for the counter
is effective when input is "High", and invalid when input is "Low". If
unconnected, it is a pull-up in the board (card) and remains "High".
Therefore the external clock for the counter is effective when the
counter gate control input is not connected.
CAUTION
-
Do not short the output signals to analog ground, digital ground, and/or power line. Doing so
may damage the board.
-
Do not connect a digital output signal to any other digital output, either on the board or on an
external device, as this may cause a fault on the board.
-
Analog ground of CN1 is isolated from the ground in the PC.
Block Diagram
Difference from ADAI16-8/2(LPCI)L
The functions same with conventional product of ADAI16-8/2(LPCI)L
are provided with the AIO-160802LI-PE. In addition, as there is
compatibility in terms of connector shape and pin assignments, it is
easy to migrate from the existing system. So you can use the same
operating procedures as ADAI16-8/2(LPCI)L.
There are some differences in specifications as shown below.
AIO-160802LI-PE
ADAI16-8/2(LPCI)L
Power
consumption
+3.3VDC 1100mA (Max.)
+5VDC 680mA (Max.)
Bus specification
PCI Express Base
Specification Rev. 1.0a x1
PCI (32-bit, 33MHz,
Universal key shapes supported)
Dimension (mm) 169.33(L) x 110.18(H)
121.69(L) x 63.41(H)
Weight
120g
65g
Analog Ground
Shield cable
Analog Output 0..3*2
BOARD
CN1
Target
Digital Input
Digital Ground
BOARD
CN1
Cable
Target
10k
Ω
Digital Ground
BOARD
CN1
Cable
Target
Digital Output
I
OL
=16mA
8 Single-end
Analog Inputs
4 Digital Inputs / 4 Digital Outputs
External Trigger Inputs
Counter Input / Output
PCI Express bus
CN1
2 Analog Outputs
DC/DC
converter
FPGA
Multiplexer
OP
Amplifer
A/D
Converter
OP
Amplifer
OP
Amplifer
DA
Converter
DA
Converter
Isolator
Buffer
PLUG-IN Electronic GmbH • Am Sonnenlicht 5 • 82239 Alling • Tel.: +49 (0) 8141 3697-0 • [email protected] • www.plug-in.de
