Contacta STS-K072 страница 5 Скачать руководство пользователя

Страница: 5 / 16

We recommend that installation is carried out by a qualified engineer,

adhering to relevant standards.

Check the contents of the box to familiarise yourself with the components.

Installation Instructions

A basic toolkit recommended to install the system will include:

Trim cables if necessary (excluding the power supply)

to the required length to connect to the back of the

amplifier. Bare approximately 6mm of the cable ends to

connect to the 2 pin plugs.

• Wire Cutters/Strippers

• Tape Measure

• Pencil or Marker Pen

• Cable Ties

• Trunking

•

Screwdrivers (Flat or Blade 2.5mm

and Phillips Head PH2)

• Battery or Mains Drill

• Drillbits: 2mm, 3mm, 5mm and 7mm

• Cable Tacking Gun (10mm)

Recommended Tools

Staff Counter Side

Customer / Visitor

Counter Side

Staff Pod

Screen Mounted

Microphone

Speaker Pod

Negative -

or screened cable

Содержание STS-K072

















Результаты поиска

Содержание STS-K072

Отзывы:

Похожие инструкции для STS-K072

Бренды по названию

Популярные бренды

Contacta STS-K072, Инструкция по установке и эксплуатации

Результаты поиска

Содержание STS-K072

Отзывы:

Похожие инструкции для STS-K072

Бренды по названию

Популярные бренды