Constructor 5411074210182, Оригинальное руководство пользователя, Страница: 29 / 36

Switching ON / OFF
For your safety use both hands
to switch the power tool on and
off.
▪
Connect the power tool to the power supply.
▪
To switch on the machine, press the main switch
(13).
▪
To switch off the tool, you must release the on / off
switch (13).
▪
Important! Place the material you want to saw
flat on the machine surface and secure with
the clamping device (10) so that the material cannot
move while you are cutting.
▪
After switching on the saw, wait for the blade (2)
to reach its maximum speed.
▪
Press the release lever (14) sideways and,
using the handle, apply steady and light
downward pressure to move the machine head
through the workpiece.
▪
When the cut is completed, return the machine
to its top parking position and let go of the
On/Off switch.
Caution! A return spring causes the machine head
to rise automatically at the end of the cut.
Do not let go of the handle as soon as the cut is
completed but steady the machine head and allow it
to rise slowly.
Laser
▪
ON / OFF switch (23)
▪
The laser (20) directs a beam onto the
workpiece
▪
Extremely precise cuts can be made using the
laser function.
Dust bag
To attach the dust bag (16), fit it onto the dust
extraction adapter. When the dust bag is about
half full, remove the dust bag from the tool and
empty it.
Sawing
Make sure the saw blade
doesn’t block while you are
sawing. It causes
damage to and burning of the
motor. If there is a blockade of
the saw blade,
please loosen the switch
immediately to prevent damage
at the motor.
▪
Clamp the work piece firmly.
▪
Set the required horizontal mitre angle or the
required vertical bevel angle.
▪
Switch on the power tool.
▪
Move the handle (12) slowly downwards.
▪
For long workpieces you should use the slide;
loosen the locking knob for this purpose.
▪
Saw trough the work piece.
▪
Switch off the power tool.
▪
Wait until the saw blade (2) has come to a
complete standstill before removing the work piece.
Sawing special work pieces
Curved or round work pieces need to be secured
against slipping.
Make sure there is no gap between the work piece
and the fence (4) or the saw table (5).
Replacing the saw blade
Disconnect the tool from the
outlet before working on the saw
blade.
Wait a while before touching the
saw blade. It can be very hot.
The teeth of the saw blade are
very sharp.
▪
Press the release lever (14) and fold up the
removable blade guard (1).
▪
Press the spindle lock knob to activate it, turn
the saw blade (2) by hand until it
locked.
▪
Loosen the blade lock bolt by turning it
clockwise using the Allan key.
▪
Remove the lock bolt, outer flange, saw blade
▪
Remove the chips or sawdust from around the
spindle and flanges.
▪
Fit the new saw blade, flanges and lock bolt.
Check that the blade rotation direction
complies with that of the motor.
When replacing the saw blade,
you can tighten the slide bar
with the locking knob.
CLEANING AND MAINTENANCE
Before performing any work on
the equipment, pull the power
plug.
Service
§ Only qualified specialist personnel and original
replacement parts should be used for repairs. This
will ensure that your device remains safe.
Cleaning
▪
Regularly clean the machine housing with a soft
cloth, preferably after each use.
▪
If the dirt does not come off use a soft cloth
moistened with soapy water.
▪
Never use solvents such as petrol, alcohol,
ammonia water, etc. These solvents may
damage the plastic parts.
Lubrication
The machine requires no additional lubrication.