Constructor 5411074210182, Оригинальное руководство пользователя

Страница: 27 / 36

DESCRIPTION
1. Protective hood
2. Saw blade
3. Side support bar
4. Fence
5. Saw table
6. Table lock Lever
7. Table insert
8. Scale for mitre angle (horizontal)
9. Mounting hole
10. Clamp
11. Slide bar
12. Operating handle
13. ON / OFF switch
14. Release lever
15. Retaining pin
16. Dust collection bag
17. Angle scale
18. Angle lock lever
19. Slide bar lock
20. Laser
21. Spindle lock
22. Lock screw for clamping device
23. Laser ON / OFF switch
INSTALLATION
Bench mounting
When the tool is shipped, the handle is locked in the
lowered position by the stopper pin. Release the
stopper pinby simultaneously applying a slight
downward pressure on the handle and pulling the
stopper pin.
FUNCTIONAL DESCRIPTION
WARNING:
• Always be sure that the tool is switched off and
unplugged before adjusting or checking
function on the tool. Failure to switch off and
unplug the tool may result in serious personal injury
from accidental start-up.
Blade guard
When lowering the handle, the blade guard rises
automatically.
The blade guard returns to its original position
when the cut is completed and the handle is raised.
WARNING:
• Never defeat or remove the blade guard or the
spring which attaches to the guard. An exposed
blade as a result of defeated guarding may result in
serious personal injury during operation.
In the interest of your personal safety, always
maintain the blade guard in good condition. Any
irregular operation of the blade guard should be
corrected immediately.
Check to assure spring loaded return action of
guard.
WARNING:
• Never use the tool if the blade guard or spring
are damaged, faulty or removed. Operation of the
tool with a damaged, faulty or removed guard may
result in serious personal injury.
If the see-through blade guard becomes dirty, or
sawdust adheres to it in such a way that the blade
and/or workpiece is no longer easily visible, unplug
the saw and clean the guard carefully with a damp
cloth. Do not use solvents or any petroleum-based
cleaners on the plastic guard because this may
cause damage to the guard.
DO NOT DEFEAT OR REMOVE GUARD.
• It is extremely important to always secure the
workpiece correctly with the proper type of vise
or crown molding stoppers.
Failure to do so may
result in serious personal injury and cause damage
to the tool and/or the workpiece.
•
After a cutting operation do not raise the blade
until it has come to a complete stop. The raising
of a coasting blade may result in serious personal
injury and damage to the workpiece.
- Instruction to support long workpieces cut
• When cutting a workpiece that is longer than
the support base of the saw, the material should
be supported the entire length beyond the
support base and at the same height to keep the
material level. Proper workpiece support will help
avoid blade pinch and possible kickback which may
result in serious personal injury. Do not rely solely
on the vertical vise and/or horizontal vise to secure
the workpiece.
Thin material tends to sag. Support workpiece over
its entire length to avoid blade pinch and possible
KICKBACK.
The holders can be installed on either side as a
convenient means of holding workpieces
horizontally. Slip the holder rods into the holes in the
base and adjust their length according to the
workpiece to be held. Then tighten the holders
securely with the screws.
- Fixing the machine to a workbench.
The machine must be screwed to a workbench.
■
Mark the position of the mounting holes (8) on the
workbench.
■
Drill holes at each of the marked positions,
adjusting the diameter and depth of the holes to the
screws used.
■
Place the machine on the workbench and insert
the screws into the mounting holes.
■
Firmly tighten the screws.
- Information to set the minimum size of the
pieces to be cut
Minimal workpiece sizes (= all workpieces that can
be clamped left or right from the saw blade with the
provided quick-action clamp 30 x 220mm (length x
width)