CONSTRUCTA CVC228ST, Руководство пользователя

Страница: 9 / 28

9
ZVC228-001_v01
7 The vacuum cleaner may be stored vertically or
horizontally. In order to do so, insert the fastening hook of
the combination brush to the combination brush fastener.
The hose may be attached to the vacuum cleaner, however
you have to make sure that it is not excessively bent during
storing.
8 If necessary, clean the casing and the chamber of the
vacuum cleaner with a damp cloth (it may be damped in
dishwashing liquid), dry it off, and wipe it dry.
Do not use any scrubbing agents or solvents.
Examples of problems you may encounter
when using the vacuum cleaner
PROBLEM SOLUTION
A characteristic fluttering
in the vacuum cleaner is
heard.
• Check the CYKLON dust container
and other accessories. Remove the
reason for the clog-up or empty and
clean the CYKLON dust container.
• Replace or clean the filters.
The vacuum cleaner works
less efficiently.
Empty and clean the CYKLON dust
container, replace or clean the filters,
check the suction pipe, the hose, and
the nozzle – remove the reason for
the clog-up.
The cut-out of the
wiring system has been
triggered.
Check if there are any other devices,
besides the vacuum cleaner, plugged
into the same electrical circuit. If the
cut-out is triggered again, have
the vacuum cleaner repaired in
a servicing center.
The vacuum cleaner does
not work; the body or the
power cord is damaged.
Have the vacuum cleaner repaired in
a servicing center.
3 Carefully insert a new / rinsed filter to previously
occupied space.
4 Put the filter cover so that two tips located at the right
side of the cover should hit the holes in the body of the
vacuum cleaner, press the filter cover so the hook snapped
in the body. Characteristic “click” sound informs, that the filter
cover has been properly installed.
Do not use the vacuum cleaner with no inlet
and outlet filters mounted in the device.
Damaged inlet and outlet filters must be always
replaced with new, factory original filters.
THE CONE OF CYKLON DUST CONTAINER
It is necessary to clean periodically the CYKLON dust
container cone.
1 Disassembly CYKLON dust container according to
point C .
2 Press the button located on CYKLON dust container and
open the bottom of the container. If CYKLON dust container
is full, empty it according to the point C .
3 Turn the cone left, so the two tips located on the flange of
the cone were put out from the slots of the container. Put out
the cone.
4 If the CYKLON dust container cone (15) is dirty, you
can rinse it with running water. Do not forget to dry above
mentioned cone before re-installation.
5
Insert the rinsed cone of CYKLON dust container into the
container slot so the tip located on the flange of the cone was
in the slot of container’s body. Turn right the cone so that the
two tips located on the flange of the cone were blocked in the
slots of the container.
6 Snap the bottom of CYKLON dust container. Please
pay attention to the proper positioning of seal found on the
bottom of the container.
7 Insert CYKLON dust container to vacuum cleaner
chamber. The characteristic “click” indicates that the
container has been correctly mounted.
After-work procedures, cleaning, and
maintenance
1 Press the on/off button (4) to stop the vacuum cleaner.
2
Remove the plug of the cord from the socket.
3 Wind the cord by pressing the cord winder button (7) .
Hold the cord when doing it to avoid tangling the cord up or
letting the plug hit the vacuum cleaner.
4 Disconnect the telescopic suction pipe from the nozzle or
brush.
5 Disconnect the telescopic suction pipe from the hose.
6 Press the button situated on the end of the hose, and
remove the end of the hose from the inlet of the vacuum
cleaner.
F
G