7
ZVC228-001_v01
4
Install a nozzle or a brush on the other end of the suction
pipe.
5
Use combination carpet & floor brush for vacuuming both
hard surfaces and carpets. To clean hard surfaces – wooden
floors, plastic floors, ceramic tiles etc. pull out the brush by
pressing the switch on the combination brush according
to the figure
. Retract the brush when vacuuming
carpets (set the switch in “
”).
6
Grab the plug of the cord
(3)
, and pull it out of the
vacuum cleaner.
When pulling out the cord pay attention to
the yellow band which marks the end of the
cord. Any attempts to unwind the cord further
(especially forcefully pulling on it) may lead to
damaging it.
7
Put the plug of the cord in an electric socket.
Before turning the vacuum cleaner on, make sure the
CYKLON dust container is installed in the chamber of the
vacuum cleaner, and also the inlet filters and the outlet filter
are installed in the vacuum cleaner.
8
Press the on/off button to start the vacuum cleaner
(4)
.
9
The vacuum cleaner is equipped with an electronic
controller of suction power, which enables smooth regulation
of suction power of the vacuum cleaner. By moving the slider
(5)
right (MAX) and left (MIN) you may respectively increase
or decrease the suction power.
10
The vacuum cleaner is also equipped with a mechanic
suction power controller
(11)
, which is situated on the hose
handle. You may use it to slightly regulate the suction power
without the need to use the slider
(5)
.
Installing/deinstalling the CYKLON dust
container
The vacuum cleaner is equipped with a removable CYKLON
dust container (which is a removable part of the vacuum
cleaner) responsible for collecting dirt. After the CYKLON
dust container is full, it has to be emptied.
The vacuum cleaner is equipped with a safety
valve situated in the chamber of the CYKLON
dust container. It opens up automatically when
the suction hose or any elements attached to
it are completely clogged up, and when the
CYKLON dust container is overfilled. After the
valve is open, you will hear a characteristic
fluttering in the vacuum cleaner.
1
The vacuum cleaner is equipped with a CYKLON dust
container fill indicator
(6)
, and it lights on if the vacuum
cleaner is on (working at full power, and the nozzle or brush
is over the cleaned surface), when there is the need to empty
the CYKLON dust container. The CYKLON dust container fill
indicator
(6)
may also be on when the suction hose or other
accessories linked to it are clogged up.
2
Press the on/off button
(4)
to stop the vacuum cleaner.
C
Static electricity
In the process of vacuuming of some surfaces in areas of
low air humidity the device may become electrically charged.
It is a natural phenomenon – it does not damage the device,
and it is not considered to be a fault.
In order to minimize the phenomenon, we recommend you to:
●
discharge the device by touching metal items in the room
with the pipe,
●
increase air humidity in the room,
●
use widely available antistatic agents.
Design
A
1
Outlet filter cover
2
Combination brush fastening
3
Plug with the cord
4
ON/OFF button
5
Suction power regulation slider
6
CYKLON dust container fill indicator
7
Cord winder button
8
CYKLON dust container unlocking button
9
Handgrip for carrying the vacuum cleaner
10
Handgrip for carrying the CYKLON dust container
11
Bolt – a mechanic controller of suction power
12
Suction hose
13
Telescopic suction tube
14
HEPA inlet filter (installed in the CYKLON dust container)
15
Foam inlet filter (installed in the CYKLON dust container,
in the frame of the HEPA outlet filter)
16
CYKLON dust container (a removable part of the vacuum
cleaner)
17
Dust container cone CYKLON (mounted in dust container
CYKLON)
18
Outlet filter “Microfilter” (mounted in a vacuum cleaner)
19
Switch-over nozzle brush
20
Crevice nozzle
21
Small brush
22
Small nozzle
23
Turbo brush
Before first use
B
1
Put the end of the suction hose to the inlet of the vacuum
cleaner. A characteristic “click” signalizes the hose has been
properly installed.
2
Connect the other end of the hose with the telescopic
suction pipe.
3
Select the needed length of the telescopic suction pipe
by sliding the slider according to the arrow, and pulling out/in
the pipe.
