Consort DF2SL heatflow Скачать руководство пользователя страница 1

 

All electrical appliances produced by Consort are guaranteed for one year against 
faulty materials or workmanship.  This applies only if the appliance has been used for 
purposes in accordance with the instructions provided and has not been connected to 
an unsuitable electricity supply, subject to misuse, neglect, damage, modification or 
repair by any person not authorised by us. This guarantee is offered to you as an extra 
benefit and does not affect your legal rights. 

The correct electricity supply voltage is shown on the rating label attached to the 
appliance. 

Reasonable care has been taken to ensure that this guide is accurate at the time of 
printing. In the interest of progress Consort reserves the right to vary specifications without 
notice. 

O VERVIEW  

Please read this guide carefully and retain for future reference and maintenance. This 
appliance has been designed and manufactured to the highest international standards 
but care should be taken in order to achieve the best results and highest safety. This 
appliance also meets the requirements of EU Directive 2004/106/EC for EMC and 
2009/125/EC Directive. 

Содержание DF2SL heatflow








Отзывы: