58000386 Iss 02
2
Overview
Please read this guide carefully and retain
for future use and maintenance.
This appliance has been designed and
manufactured to the highest international
standards, however, care must be taken
for optimal results and safety. This
appliance also meets the requirements of
EU Directive 2004/106/EC for EMC and
2009/125/EC Directive.
Safety & Care
The appliance is not intended for use by
persons (including children) with reduced
physical, sensory or mental capabilities or
lack of experience and knowledge unless
they have been given supervision or
instruction concerning use of the
appliance by a person responsible for their
safety. Children should be supervised to
ensure that they do not play with the
appliance.
Warning
Do NOT site the appliance into a corner.
Do NOT handle the appliance with wet
hands.
Do NOT use the appliance in workshops
or rooms where excessive dust is
generated or present.
Ensure that nothing is pushed into any
aperture of this appliance.
Do NOT touch outlet grille when the
appliance is in use.
Do NOT cover or restrict any aperture of
the appliance when in use.
Do NOT use the appliance if damaged.
Do NOT leave the appliance
unattended where young children are
present.
Thermally Operated Cut-Out
The appliance is fitted with a thermally
operated cut-out (TOC). This is a safety
device, which switches the heater off if, for
any reason, the appliance overheats. The
TOC can only be re-set after the
appliance has cooled down. In order to re
-set the TOC, proceed as follows:
Switch off appliance at mains and
leave for approximately 5 minutes.
Switch appliance back on and the
TOC will re-set.
Ensure that the appliance is functioning
correctly. If the TOC control operates
again, the appliance should be checked
by a competent electrician.
The heater carries a ‘Do Not Cover’ label to warn
the user that if the appliance is covered, there is a
risk of overheating.
Cleaning
Always disconnect the heater from the mains
before cleaning. The heater should not require
any maintenance, but it is strongly advised that it
is kept clean. An occasional wipe over with a soft
cloth is all that should be necessary.
Do NOT use metal or furniture polish on any part
of the heater.
Do NOT touch the heater with wet hands or in
any way bring water into contact with it.
If the supply cord is damaged, it must be
replaced by the manufacturer or its service agent
or a similarly qualified person in order to avoid a
hazard.
If Your Heater Does Not Work
Check that power is available to the heater.
The LED light should be illuminated
Check that the thermal cut-out has not
operated. Follow the reset instructions given
under the section headed ‘Thermal Operated
Cut-out’.
Check that the fuse in the spur unit has not
blown. This can be done by replacing the fuse
with another suitable fuse.
Should neither of the above remedies work, then
telephone the helpline number shown in these
instructions (UK ONLY). Do not attempt to repair
the heater.
Connection to the Main Supply
Electrical installation should be carried out by a
competent installer, preferably registered with
NICEIC (National Inspection Council for Electrical
Installation Contracting) in accordance with the
17 edition of the IEE Wiring Regulations, (BS.7671),
and any relevant Local Authority Bye-Laws. The
Heat-Zone can be connected in a number of
ways depending on the form of control required.
Whichever method is used, it should be
permanently connected to the electricity supply
via a double pole switch having 3mm gap on
each pole. A switched Fused Connection unit to
BS.1363. Part 4 is a recommended mains supply
connection accessory to ensure compliance with
safety requirements applicable to fixed-wiring
installation.
Note: When switched on for the first time the
appliance may emit a slight smell. This is purely
the evaporation of a fluid used in the
manufacturing process.
WARNING: This appliance must be earthed.
Содержание Claudgen HE6137E
Страница 6: ...6 15 Mounting 58000386 Iss 02 ...
