background image

59

12.5.3 Resetting to Basic Setting (RESET SETUP)

If you want to reset the product to the default settings at delivery, use the following command:

RESET SETUP 12345678 #1513

All previously made settings are lost and are deleted definitely.
The PIN number of the SIM card is not changed when resetting to default. After
restart, the product therefore is unable to register again (SIM card = last PIN set,
product = 1513).
Alternatively, the product may also be manually reset. This is described in a
separate chapter.

13. Restoring Default Settings

If...
...the device no longer reacts
...the PIN number in the device was forgotten
...the product does not behave as configured
...the configuration is set to impossible values
the device can be manually reset to the factory settings.

Proceed as follows:

1. Remove the SIM card (the device switches off).
2. Insert the SIM card while pushing the „RESET“ button until LED1 flashes red.
3. When LED1 flashes red, remove the SIM card and insert it again as usual (without pushing

any buttons)..

It is decisive that the button „RESET“ is pushed at product initialisation after SIM
card insertion. In this case, the factory settings will be loaded. This is indicated by
the flashing red GSM-LED.

Содержание 841086

































































Отзывы: