• Mount the “camera support” (7) with suitable mounting material to the wall.
• Screw camera in the “camera support” (7).
• (If not already done) screw the supplied “antenna” (1) on the camera.
• Adjust the camera to the desired position.
• Fasten the locking screw on the “camera support” (7).
☞
Do not point the camera directly at a source of bright sunlight as this
could lead to over-exposure and an unclear picture.
Connecting the radio camera
• Connect the low voltage plug of the supplied plug-in power transformer to the “DC
IN 1A” (8) power connection on your radio camera.
• Plug the power transformer into a suitable mains socket.
Establish connection
After mounting and connection it is necessary to perform a connection search between
the radio camera and the radio receiver (provided in the set with order no. 751509).
For this purpose, also please observe the user manual of the 2.4 GHz digital radio
camera set, with item no. 751509.
• Select the “MENU” button on your receiver. You are directed to the set up menu.
• Select the menu item “Pair CAM” by using the keys “Up”, “Left”, “Down” or “Right”.
• Then select the desired channel (1, 2, 3 or 4). In total, 4 cameras can be selected.
• When you have selected the appropriate channel, press the “Channel-selection”
key to start the connection search. Now, you have 60 seconds to press the corre-
sponding “Pairing” (9) key, on your radio camera.
• Press down and hold the “Pairing” (9) key on your radio camera for about 5 seconds.
• After successfully establishing the connection, the corresponding camera image is
displayed on the desired channel and the “LED Link” (2) flashes on the camera.
Troubleshooting
Problem
Possible cause
Recommendation
Display
The radio camera is not
Approach the corresponding
“NO connection”
supplied with voltage.
camera and verify if the camera
is connected to the voltage.
If the camera is supplied with volt-
age, the LED “Power” (3) flashes
accordingly.
No connection search
For this purpose, see the chapter
performed yet.
“6.2 connection search” in the
operating manual of the
2.4 GHz digital radio camera set
with the item no. 751509.
The camera is
Place the camera closer
beyond coverage.
to the receiver.
On the radio camera
Make sure that the antenna
no antenna was
has been approprately screwedi
screwed on or connected. on or connected to the camera
and the receiver.
Bad
Poor antenna
Try to align the antenna
signal reception
alignment
position of the radio camera as
well as of the receiver.
Radio signal is blocked
If this is the case, ensure that
there are no sources of interfer-
ence located near the radio cam-
era or the receiver (e. g. rein-
forced concrete walls, silvered
mirrors, thermo-windows, plate
shelfs, other wireless devices
such as W-LAN routers, etc.)
Maintenance and Cleaning
Before cleaning the housing of the surveillance camera, separate it from the mains volt-
age and disconnect the mains adapter from the mains socket.
To clean the outside of the camera, it is sufficient to use a dry, soft and clean cloth. For
heavier soiling of the camera, you can moisten the cloth slightly with lukewarm water.
Clean the lens very carefully, otherwise you may scratch it.
Disposal
Electrical and electronic products do not belong to the household
waste!
Please dispose of the device, when it is no longer of use, according
to the current statutory requirements.
Technical Data
a) Radio camera
Operating voltage:
5 V/DC, 1A
Frequency :
2.4 GHz
Operating temperature range:
-10° to +40°
IP44
Number of IR LEDs:
23
Max. IR range:
8 metres
Wireless range:
max. 200 meters (free vision)
b) Mains transformer
INPUT
230 V/AC 50 Hz, 0.18A
OUTPUT:
5 V/DC, 1A
Declaration of conformity
We, Conrad Electronic, Klaus-Conrad-Strasse 1, D-92240 Hirschau, Germany, her-
eby declare that this product complies with the fundamental requirements and the
other relevant provisions of Directive 1999/5/EC.
☞
The declaration of conformity of this product is available at
www.conrad.com or on the website of the manufacturer.
These operating instructions are a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240
Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or
the capture in electronic data processing systems require the prior written approval by the editor.
Reprinting, also in part, is prohibited.
These operating instructions represent the technical status at the time of printing. Changes in
technology and equipment reserved.
© Copyright 2009 by Conrad Electronic SE.
