ConMed Hall MicroPower 6020-026 Скачать руководство пользователя страница 29

Страница: 29 / 40

3.2

Troubleshooting

Table 4: Troubleshooting

Symptom

Possible Cause

Corrective Action

Handpiece does not
operate.

♦

Handpiece cord not connected
securely.

♦

Handpiece cord and/or button
faulty.

♦

Handpiece faulty.

♦

If using a footswitch, cord not
connected securely.

♦

Footswitch cord or footswitch
faulty.

♦

Handpiece safety is in the safe,
or off position.

♦

Twist collet not in the fully
locked position.

♦

Securely connect handpiece cord
to handpiece and controller.

♦

Replace handpiece cord.

♦

Return for service.

♦

Securely connect footswitch cord
to controller receptacle.

♦

Return for service.

♦

Move safety to the appropriate
operating position.

♦

Twist collet to the fully locked
position.

Handpiece overheats

♦

Worn bearings in the bur
guard.

♦

Moisture in the handpiece.

♦

Reference “3.3 Bur Guard Test-
ing Procedure” on page 26. If
resistance is noticed, return bur
guard for service. If no resistance
is noticed, return for service.

♦

Resterilize the handpiece accord-
ing to sterilization parameters and
drying times, reference “3.1.4
Sterilization Information” on
page 23.

“Magnetic Field”

is displayed on the
controller.

♦

The handpiece is in close
proximity to a magnetic drape.

♦

Removable activation lever
partially connected.

♦

Faulty handpiece.

♦

Remove the handpiece from the
magnetic drape area. Wait five
seconds before restarting.

♦

Completely connect the activation
lever (See “2.3.4 Removing the
Detachable Handpiece Activa-
tion Lever” on page 16).

♦

Return handpiece to ConMed
Linvatec for service.

Содержание Hall MicroPower 6020-026








































Результаты поиска

Содержание Hall MicroPower 6020-026

Отзывы:

Похожие инструкции для Hall MicroPower 6020-026

Бренды по названию

Популярные бренды

ConMed Hall MicroPower 6020-026, Инструкция по эксплуатации

Результаты поиска

Содержание Hall MicroPower 6020-026

Отзывы:

Похожие инструкции для Hall MicroPower 6020-026

Бренды по названию

Популярные бренды