background image

2

Stand up both side
panels [A].  Insert
panel brace [B] into
opening located on
[A] then push down
to lock in place. 

Step 1

With the thin edge of
the curved riser [C]
facing downward
align the lower tabs
with the openings on
part [A] and push in.
Note risers must be
curved inward.

Step 2

While holding lower
tabs in part [A] align
the top tabs then tap
down with a rubber
mallet until flush.

Step 3

Install the rest of
the curved risers
[C] by flexing the
side panels [A] 
outward enough to
insert part [C] tabs
into part [A]. Tap
into place with 
rubber mallet.

Step 4

Confer Plastics “CURVE” In-Ground Pool Step

must be assembled with the treads and risers curved inward  

The CURVE Step requires 40 lbs. of sand to complete assembly. The Curve Step with optional add-on requires a
total of 70 lbs. of sand. Choose a location close to the swimming pool for assembly. 

Hardware Pack

2 - Plugs [WG]
8 - #10 x 1-1/4" screws
2 - Labels-No Jumping/Diving

Hardware not provided to
fasten step to concrete.
Purchase locally.

Needed for Assembly

- Rubber mallet
- Funnel
- Cordless Drill
- Phillips screwdriver
- Liquid soap or lubricant
- Sand - 40 lbs. for (Curve Step)

- 70 lbs. for (Curve System)

Model# CCX-IG

CURVE IN-GROUND POOL STEP 

ASSEMBLY INSTRUCTIONS - PLEASE READ BEFORE ATTEMPTING ASSEMBLY

Parts List

2 - Side panels [part A]
1 - Panel brace [part B]
3 - Curved risers [part C]
4 - Handrail posts [part E]
2 - Deck connectors [part F]
2 - Handrails [part G]
4 - Foot pads [part H]
2 - Treads [part I]
1 - Top tread [part I-3]

If missing parts call - Toll free U.S. - 800-635-3213 or www.Conferplastics.com

G

I

C

F

I-3

E

B

A

H

prpd.Confer-CurveStepIGr17_Confer-Step-1_R1  6/21/13  8:40 PM  Page 2

Содержание CCX-IG









Отзывы: