3
er
ill
d
11.
1
C
am
tu
as
3
Separate the swing up assembly from the
ladder legs and set aside.
9.
Slide (2) two handrails up through the bot-
tom of the platform using the openings next
to the round tabs. Leave the flat ends of the
handrails exposed.
10.
2
W
po
po
do
sw
to
re
2
P
M
aw
po
to
tw
R
6.
7.
Stand the assembly up on edge and place
the tread connector over the square ends on
the (4) four treads. The large oval hole on
the tread connector must be on the same
end as the flat side on the ladder legs.
Using a rubber mallet tap the tread connec-
tor onto the square ends of the treads until
they are firmly seated. A little liquid soap on
the tread end will help.
Flip assembly over and repeat step 7 to
attach the second tread connector.
Overlap the flat end of the ladder leg onto the flat
end of the handrail. Insert one of the ¼ - 20 x 1”
bolt through the ladder leg into the handrail. Place
one of the ¼ - 20 hex nuts into the recessed area
on the handrail and tighten using a Phillips
screwdriver. Install the second nut and bolt.
14.
Attach the second ladder leg to the handrail
by repeating step #11.
12.
Stand the ladder up, using a rubber mallet tap the
platform down until seated on the lugs on the ladder
leg. IT WILL REQUIRE SEVERAL HARD BLOWS
WITH A RUBBER MALLET TO SEAT THE PLAT-
FORM ALL THE WAY DOWN ONTO LUGS.
13.
Attach the standard tread to the bottom of
the ladder as shown.
17.
Slide the (2) two adjustable tube handrails up
through the bottom of platform until seated on
the lugs.
15.
Flex the oval openings on the swing up
assembly (from step #9) over the two round
tabs on the platform. Using a rubber mallet
tap down on the tread connector until seat-
ed over the round tab. It may require sev-
eral hard hits with a rubber mallet to get
tread connector over round tabs.
16.
Using a #10 x 1-1/4” screw fasten the
upper ends of the handrails together as
shown. Repeat for opposite side.
Insert screws here
8.
prpd.RG-Confer 8100X-11-13_Confer 6100_12-05_R1 11/22/13 9:15 AM Page 3
Hardware Pack
14- #10 x 1-1/4" screws
2 - Plugs (wg)
2 - 1/4 - 20 x 2" Bolts
2 - 1/4 - 20 Acorn Nuts
2 - Adjustable Tubes
2 - Mounting Blocks
4 - 1/4 - 20 x 2 1/4" Bolts
4 - 1/4 - Flat Washers
8 - 1/4 - 20 Hex Nuts
4 - 1/4 - 20 x 1" Bolts
1 - Padlock
Needed for Assembly
- Rubber mallet
- Phillips screwdriver
- Adjustable wrench
- Liquid soap or lubricant
- Cordless Drill / Phillips Driver
- 5/16” Drill bit
Model #8100X
Outside Safety Ladder
ASSEMBLY INSTRUCTIONS - PLEASE READ BEFORE ATTEMPTING ASSEMBLY
Parts List
2 - Ladder Legs
2 - Tread Connectors
4 - Swing up Treads
1 - Standard Tread
2 - Extension Boots
1 - Platform
2 - Handrails
2 - Adjustable Tube Handrails
If missing parts call - Toll free U.S. - 800-635-3213 or www.Conferplastics.com
For Use with Confer Plastics In-Pool Step
ADJUSTABLE
TUBE
HANDRAILS
TREAD
CONNECTIORS
SWING UP
TREAD
MOUNTING
BLOCKS
PLATFORM
LADDER
LEGS
1.
Place (2) two ladder legs on a flat
surface. Using a Phillips screwdriv-
er tap out the plastic film from the
three holes on the bottom of
each leg.
Using two 1/4-20 x 2” long bolts and
two acorn nuts fasten the extension
boots to the ladder legs
Slide (4) four of the swing up treads
over the ladder legs as shown.
2.
3.
Slip the (2) two extension boots over
the ends of the ladder legs. They will
need to be all the way on if the
outside dimension is 52" and backed
off one hole if the outside dimension
is 54".
4.
5.
2
STANDARD
TREAD
Se
lad
9
HANDRAIL
6
St
th
th
th
en
Extension boots are not required if
the outside height of your pool
(measured from the ground to the
top of the pool ledge) is 48" or less.
If this measurement is more than
48" extension boots will be
required. Using a Phillips screwdriver
tap out the plastic film from the top
hole on each side of the extension
boots.
At
by
1
Sl
th
th
ADJUSTABLE
TUBES
EXTENSION
BOOT
prpd.RG-Confer 8100X-11-13_Confer 6100_12-05_R1 11/22/13 9:15 AM Page 2
