background image

CGU 04i   DESCRIPTION 

39 

Parameter name 

Set value range  

Parameter description 

GPRS – enable 
duplicate registration 

YES/NO 

When the station is Local DNS server, then 
this parameter enable logging of the modem 

with dynamical IP address to network.
The modem changes own IP address after 
some time and then tries log on to network 
with the same interface address. In this case 
the Local DNS server thinks that the next 
modem log on to the network with the same 

interface address and decline it. 

GPRS – 
communication 
speed 

--- 

Communication speed between modem CPU 
and GSM/GPRS module information. 

GPRS – registration 
period 

0 up to 999999 s 

Registration period is time how often the 
modem repeats first log in to the local DNS. 

GPRS – Heart Beat 
period 

0 up to 255 min 

Heart beat period is time when the modem 
repeats log in to the local DNS after 
successful log in. By this the modem checks 
active connection with local DNS. 

GPRS – timeout for 
disconnection 

0 up to 255 s 

The modem checks CTS control signal from 
module. If the CTS signal is inactive after this 
timeout the GPRS connection is inactive and 
will be new log in to the GPRS. 

Acknowledge time 
out 

100 up to 25500 

msec 

After this timeout the modem wait to sent 
message acknowledge. 

Transmit attempts 

1 up to 5 

Parameter sets the maximal number of data 
transmission repetition. 

Packet maximum 
length 

128 up to 1000 

Parameter set maximal possible length
of sending data message, the 

maximal 

adjustable message length is 1000 bytes. 

Attempts for PPP init 
connection 

1 up to 16 

Parameter set attempts number of
the transmitted control LCP/IPCP frames 
behind PPP connection establishment. 

Firmware version 

--- 

Parameter shows modem firmware number, 
only for information. 

Automatic reset 
interval 

0 up to 999999 min

Parameter set period after which the modem 
will be reset. 

Transferred data limit 

0 up to 65535 kB 

If this data limit is proceed it will send size 

data information to the global DNS. The data 
communication is next allowed and possible. 

GPRS – firmware 
version 

--- 

IGSM/GPRS module firmware version 
information. 

Содержание CGU 04i

























































Отзывы: