background image

16

SERIES L12 RADIO MANUAL

P/N 701L12005.2.0

7.4  Password Operation

1. Rotate EMS mushroom clockwise and pull out.

2. Turn key clockwise to “ON” position.

3. Press the pushbutton sequentially to enter password within 10 seconds (Remark: This time duration of “Password Enter” can be set by 
software. At the time of “Password Enter” the LED indicator will flash with green color).

4. The buzzer of the transmitter will sound one-long beep sound to indicate the password is correct. After buzzer turns off, “Power-On” according 
to the proper procedure and return to normal operation.

5. If password is incorrect, then the buzzer will sound with two (2) short beeps and one (1) long beep. Enter the correct password again after 
buzzer has turned off.

NOTES:

1. The function of the password can be set by the software in order to avoid unauthorized people from using the remote.

2. One must re-enter password to return to normal operation if EMS mushroom has been pressed (or “emergency stop” signal has been 
transmitted due to transmitter auto power off).

3. Turning key switch to “OFF” and back to “ON” will not require re-entry of password.

7.0 Function Settings

Содержание L12 SERIES





















Отзывы: