Condair TE Series Скачать руководство пользователя страница 31

Страница: 31 / 44

Fault Isolation

Condair TE

7.4

Warnings and Faults

Warnings and faults for the humidifier are indicated by the alarm light on the remote controller and by

LEDs on the humidifier control unit. When receiving an alarm, find the humidifier with the problem (using

the Find button on the remote control), then inspect the LEDs on the control unit. Refer to the table below

to understand the LEDs, and resolve the issue before resetting the alarm.
For more detailed descriptions on general issues, refer to

“Troubleshooting” on page 31

Table 11: LED Fault Patterns (refer to

“Control Unit” on page 12

)

LED No. LED Illumination Pattern

Description

Solution

LED 1

LED 1 Blinks quickly (0.1-sec

ond intervals).

Occurs when there is a communica

tion error.

This may be due to incorrect wiring,

loose wires, damaged wires, or

excessive wiring lengths.

Check the wires between the remote

controller and the main humidifier, and

check the wires between the humidifi

ers in the group.

Reconnect and secure any loose

wiring. Replace damaged wires. Ensure

wire lengths are as short as possible.

LED 1

LED 2

LED1 blinks slowly (0.5-sec

ond intervals).

LED 2 blinks quickly (0.1-sec

ond intervals).

Occurs after 950 000 counts of

operation. The unit stops operating,

but can be restarted.

Press and hold the power button for 10

seconds to restart the unit.

Water supply unit to be replaced soon.

LED 1

LED 2

LED 1 blinks quickly

LED 2 illuminates.

Occurs after 1 000 000 counts of

operation (approx. 5 years, at 5000

hours per year). The unit stops oper

ating and an alarm signal is created.

Replace the water supply unit.

LED 3

LED 3 illuminates

Occurs when the water level in the

drain pan is too high.

This may indicate an error with the

drain pump, or a blockage at the

drain pan.

Inspect the drain pain for blockages

and clear them if present. Check the

drain pump for damage or malfunction.

Check DIP switch settings DS1 for cor

rect water volume rate (refer to section

5.6.1 on page 14

)

LED 4

LED 4 Illuminates

Occurs when a water leakage is

detected in the humidifier.

The water droplet collection panel

above the drain pan contains a water

leakage sensor on its surface. This

error may indicate an issue with

foaming, water spraying or leaking

out of the supply or drain line.

Check the supply headers feeding

water to the humidification module. The

headers may be blocked with sediment.

Check the hoses/pipes inside the unit

for holes or cracks.

Check DIP switch settings DS1 for cor

rect water volume rate (refer to section

5.6.1 on page 14

Clean or rinse the humidification

module.

Replace parts as necessary.

LED 5

LED 5 Illuminates

Occurs when water supply solenoid

valve leakage or drain error in drain

pump.

Check the water supply solenoid valve

or drain valve for damage or blockages.

Check DIP switch settings DS1 for cor

rect water volume rate (refer to section

5.6.1 on page 14

)

Clear the blockage, or replace the part.

LED 7

LED 7 Illuminates

Occurs when drain error in drain

pump.

Check the drain valve for damage

or blockages. Check the drain hose/

pipe installation (proper incline, proper

heights and sizes, etc.). Check DIP

switch settings DS1 for correct water

volume rate (refer to section

5.6.1 on

page 14

)

Clear the blockage, reconfigure the

installation, or replace the part.

Содержание TE Series













































Результаты поиска

Содержание TE Series

Отзывы:

Похожие инструкции для TE Series

Бренды по названию

Популярные бренды

Condair TE Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание TE Series

Отзывы:

Похожие инструкции для TE Series

Бренды по названию

Популярные бренды