Condair TE Series Скачать руководство пользователя страница 32

Страница: 32 / 44

Fault Isolation

Condair TE

7.5

Troubleshooting

7.5.1

Humidifier does not operate

Remote Controller

Display

Possible Cause of Failure

Action

All indicator lights

are not illuminated

The humidifier power source's leakage current circuit breaker

is OFF or a power outage has occurred

Supply power from the power source

The correct power source type (120 VAC) is not being used

Confirm and rectify

The unit is toggled to OFF on the remote controller (operation

button has not been pressed)

Press the operation button

A fuse (in the control unit) has blown

Contact Condair

Board power switch SW1 is toggle to OFF

Toggle board power switch SW1 to

Alarm indicator

light blinks

Address setting has not been carried out

Carry out address setting (refer to the

installation manual)

Normal indicator

light displays

The fan does not operate during the initial water supply phase

(10 min. duration)

This is normal; the fan will begin

operating after the initial water supply

phase is complete

Power indicator

light blinks

The light is blinking slowly (0.5-sec. intervals) to indicate a

water supply unit operation count of 950,000

Press and hold the operation button

for 10 sec. or longer to cancel;

Prepare a new a water supply unit

The light is blinking quickly (0.1-sec. intervals) to indicate a

water supply unit operation count of 1 million

Replace the water supply unit

7.5.2

Humidifier is operating but humidification is insufficient

Remote Controller

Display

Possible Cause of Failure

Action

Normal indicator

light displays

The fan speed is set to low

Switch to high fan speed

The water supply service valve is closed

Open the water supply service valve

Holes in the water supply strainer are clogged, which reduces

supply water volumes

Clean the water supply strainer

Supply water pressure is too low, resulting in insufficient sup

ply water volumes

Confirm and rectify

Water supply has been cut off

Confirm

The humidistat setting is too low

Confirm settings

The humidistat is malfunctioning (contact does not switch to

ON)

Repair or replace

Fan air output is low due to filter clogging

Clean the filter

The humidification module has become dirtied, reducing

its ability to absorb water and thus reducing humidification

performance

Clean or replace the humidification

module

A water supply header nozzle(s) has become dirtied, prevent

ing even dripping of supply water (inconsistent distribution)

Clean the water supply header

nozzle(s)

A water supply header nozzle(s) has become clogged,

preventing supply water from being dripped from the affected

nozzle(s)

If no improvement is seen after trying

the above response measures: Con

tact Condair (for purposes of remov

ing the header nozzle clog(s))

No supply water is dripping down from any of the water supply

header nozzles, or only a very small amount is dripping down

Clean the water supply header

nozzle(s)

Orifices within the supply water hose are clogged, resulting

in no or very little supply water drip from the water supply

header

If no improvement is seen after trying

the above response measures:

Contact Condair (for purposes of

removing the clogging or replacing the

supply water hose)

A reason not listed above

Contact Condair

Содержание TE Series













































Результаты поиска

Содержание TE Series

Отзывы:

Похожие инструкции для TE Series

Бренды по названию

Популярные бренды

Condair TE Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание TE Series

Отзывы:

Похожие инструкции для TE Series

Бренды по названию

Популярные бренды