Condair TE Series Скачать руководство пользователя страница 13

Страница: 13 / 44

Operator Interface

Condair TE

4.2

Control Unit

VKCU-2

SW1

Lot

No.

CN4

リモコン

/HS/

瞬時常時

ON/

瞬

CN12

排水用運転信号

CN14

電源

RY5

CN16

外部信号

RY2

RY1

RY5

RY3

RY4

SSR1

CN2

給水電磁弁給水遮断弁

CN15

外信運転

ドレン排水用ポン

プ

フ

ァン出力

OFF

DS2

LED2

LED1

LED3

LED4

LED6

LED7

LED5

DS1

DS3

BS1

リセット

LED1

LED2

LED3

LED4

LED6

LED7

LED5

Reset

BS1

OFF

1 2 3 4

DS1

1 2

DS2

1 2 3 4

DS3

1 2 3 4

DS4

OFF

DS4

Figure 5:

DIP switch location (cover removed)

Before operating the DIP switch, ensure the humidifier power source’s leakage current circuit breaker is

turned to the OFF position, and power supply has been completely stopped. Changing any DIP switch

pin while power is still being supplied to the unit may result in settings not being properly implemented.
LED lights on the control unit indicate the status of the humidifier, including faults. Refer to the table

below for their definitions.

Table 3: LED pattern

LED No.

(Colour)

LED Illumination Pattern

LED 1 (green)

Blinks slowly (0.5-second intervals) when communicating with remote controller, and blinks quickly

(0.1-second intervals) when a communication error has occurred.

LED 2 (yellow)

Blinks or solidly illuminates in accordance with water supply unit operation count: 0.5-interval blinking to

indicate 500,000 times or more, 0.1-second interval blinking to indicate 950,000 times or more, and solid

illumination to indicate 1 million times (approx. 5 years, at 5000 annual hours of operation per year).

LED 3 (red)

Illuminates to indicate detection of high water level in drain pan (press reset button BS1 to cancel illumina

tion).

LED 4 (green)

Illuminates to indicate detection of water leakage (press reset button BS1 to cancel illumination).

LED 5 (yellow)

Illuminates to indicate detection of water supply solenoid valve leakage or drain error in waste water drain

age pump (press reset switch BS1 to cancel illumination).

LED 6 (red)

Reserved.

LED 7 (green)

Illuminates to indicate detection of drain error in drain pump (press reset button BS1 to cancel illumina

tion).

LED 10 (green) Illuminates when drain pump is in operation.

Board power switch

Control unit cover

Screws

default: All pins set to OFF

Содержание TE Series













































Результаты поиска

Содержание TE Series

Отзывы:

Похожие инструкции для TE Series

Бренды по названию

Популярные бренды

Condair TE Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание TE Series

Отзывы:

Похожие инструкции для TE Series

Бренды по названию

Популярные бренды