Condair GC 130 Скачать руководство пользователя страница 21

Страница: 21 / 72

Operator Interface

Condair GS

xxxxxxx_A_EN_1905_Condair-GS_OM

4.2.6 Main Menu

Select the <Menu> button on the Home screen to view the Main menu. The Main menu and its contents

are password-protected. Refer to

Figure 7

. Enter the password

"0335"

to access the Main menu.

Figure 7: Main Menu Access

The structure of the Main menu and its sub-menus is shown in

Table 6

Table 6: Main Menu Structure

"Main Menu" on

page 21

"Configuration Menu" on

page 21

"Features Menu" on

page 22

"Water Management Tab" on page 22
"Operation Tab" on page 24

"Control Settings Menu"

on page 25

"Basic Tab" on page 25
"PI Control Parameters Tab" on page 26
"RH Alerts Tab" on page 27
"Multi-Unit Operation Tab" on page 28

"General Menu" on

page 30

"Basic Tab" on page 30
"Time Date Tab" on page 30

"Communications Menu"

on page 31

"Remote Enable Tab" on page 31
"IP Parameters Tab" on page 31
"BMS Timeout Tab" on page 32
"Modbus Parameters Tab" on page 32
"BACnet Parameters Tab" on page 32
"Remote Fault Board" on page 34

"Service Menu" on

page 35

"Humidifier Service Tab" on page 35
"General Service Tab" on page 35
"Fault/Service History Tab" on page 36
"Diagnostics Tab" on

page 36

Input Diagnostics
Output Diagnostics
Relay Diagnostics

"Setpoint" on page 37
"Administrator Menu" on

page 38

"Password Setting Tab" on page 38
"Software Settings Tab" on page 39

4.2.6.1

Configuration Menu

The Configuration menu lets you configure the operation of the

Condair

GS humidifier. The menu and

sub-menu items are discussed below. Refer to

Table 6 on page 21

for the menu structure.

Содержание GC 130









































































Результаты поиска

Содержание GC 130

Отзывы:

Похожие инструкции для GC 130

Бренды по названию

Популярные бренды

Condair GC 130, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание GC 130

Отзывы:

Похожие инструкции для GC 130

Бренды по названию

Популярные бренды