Concept2 Sentinel S100, Инструкция по установке и эксплуатации, Страница: 22 / 31

● Setting Fluid Capacity. ​ In the “Setting Fluid Capacity” display press ​ Enter/Back ​ to show the current fluid
capacity set. Use ​ Up ​ and ​ Down ​ buttons to move up and down to select 500ml, 1,000ml, 5,000ml or “Fluid
Sensor on”. Only “500ml” or “5,000ml” should be used on the S70 and S100; see the “Fluid Management”
section for information on the latter. Press ​ Enter/Back ​ to save the new setting and return to the higher level
menu. Press ​ Function/Escape ​ to return to the higher level menu without saving changes. The delivery Fluid
Capacity Setting is “Fluid sensor on”.
● Setting Temperature. ​ This is preset at manufacture and should only be altered by Concept Smoke Screen.
● Setting Smoke Mode. ​ In the “Setting Smoke Mode” display press ​ Enter/Back ​ to show the current smoke
mode set. Use the ​ Up ​ and ​ Down ​ buttons to move up and down to select “Turbo Mode” or “Normal Mode”.
Press ​ Enter/Back ​ to save the new setting and return to the higher level menu. Press ​ Function/Escape ​ to
return to the higher level menu without saving changes. The delivery Smoke Mode Setting is “Turbo Mode”.
● Invert Trigger Mode. ​ In the “Invert Trigger Mode” display press ​ Enter/Back ​ to show the current trigger mode
set. Use ​ Up ​ and ​ Down ​ buttons to move up and down to select “N/O Mode” (unit detects a normally open
circuit going closed to activate) or “N/C Mode” (unit detects a normally closed circuit going open to activate).
The Set, Trigger and Hold-off modes are always the same and changing this setting changes all 3 at once.
Press ​ Enter/Back ​ to save the new setting and return to the higher level menu. Press ​ Function/Escape ​ to
return to the higher level menu without saving changes. The delivery Trigger Mode Setting is “N/C Mode”.
●
Enable / Disable Battery. ​ In the “Enable / Disable Battery” display press ​ Enter/Back ​ to show the current
battery setting. Use the ​ Up ​ and ​ Down ​ buttons to move up and down to select “Disable” or “Enable”. Press
Enter/Back ​ to save the new setting and return to the higher level menu. Press ​ Function/Escape ​ to return to
the higher level menu without saving changes. The delivery Battery Setting is “Enable”. ​ NB: the function of
the battery switch is described in the “Battery Management” Section.
●
Enable / Disable ESM (Energy Saving Mode). ​ In the “Enable / Disable ESM” display press ​ Enter/Back ​ to
show the current ESM setting. Use the ​ Up ​ and ​ Down ​ buttons to move up and down to select “Disable” or
“Enable”. Press ​ Enter/Back ​ to save the new setting and return to the higher level menu. Press
Function/Escape ​ to return to the higher level menu without saving changes. The delivery ESM Setting is
“Disable”.
● Smoke Delay.
​
In the “Smoke Delay” display press
​
Enter/Back
​
to show the current smoke delay set. Use the
Up
​
and
​
Down
​
buttons to move up and down to select a time between 0 and 60 seconds in 1 second
intervals. Press
​
Enter/Back
​
to save the new setting and return to the higher level menu. The delivery Smoke
Delay Setting is “0 seconds”.
● Verify Timer. ​ In the “Verify Timer” display press ​ Enter/Back ​ to show the current verify time set. Use the ​ Up
and ​ Down ​ buttons to move up and down to select a time between 0 and 3600 seconds in 5 second
intervals. Press ​ Enter/Back ​ to save the new setting and return to the higher level menu. The delivery Smoke
Delay Setting is “0 seconds”.
● EN Mode. ​ This is preset at manufacture and should only be altered by Concept Smoke Screen.
22