Comtrend Corporation L9VVR3060U Скачать руководство пользователя страница 10

Страница: 10 / 121

Chapter 2 Installation

2.1 Hardware Setup

Follow the instructions below to complete the hardware setup.

Non-stackable

This device is not stackable – do not place units on top of each other, otherwise
damage could occur.

BACK PANEL

The figure below shows the back panel of the device.

Power ON
Press the power button to the OFF position (OUT). Connect the power adapter to the

power port. Attach the power adapter to a wall outlet or other AC source. Press the
power button to the ON position (IN). If the Power LED displays as expected then
the device is ready for setup (see section

2.2 LED Indicators

Caution 1:

If the device fails to power up, or it malfunctions, first verify that the

power cords are connected securely and then power it on again. If the

problem persists, contact technical support.

Caution 2:

Before servicing or disassembling this equipment, disconnect all power

cords and telephone lines from their outlets.

Reset Button
Restore the default parameters of the device by pressing the Reset button for 10

seconds. After the device has rebooted successfully, the front panel should display
as expected (see section

2.2 LED Indicators

for details).

NOTE: If pressed down for more than 60 seconds, the VR-3060 will go into a

firmware update state (CFE boot mode). The firmware can then be
updated using an Internet browser pointed to the default IP address.

Содержание L9VVR3060U


























































































































Результаты поиска

Содержание L9VVR3060U

Отзывы:

Похожие инструкции для L9VVR3060U

Бренды по названию

Популярные бренды

Comtrend Corporation L9VVR3060U, Руководство пользователя

Результаты поиска

Содержание L9VVR3060U

Отзывы:

Похожие инструкции для L9VVR3060U

Бренды по названию

Популярные бренды