Comtrend Corporation CT-5624S Скачать руководство пользователя страница 71 | Manualshive

Страница: 71 / 90

background image

9.1.3 Restore

Default

Clicking the Restore Default Configuration option in the Restore Settings screen
can restore the original factory installed settings.

NOTE:

This entry has the same effect as the hardware reset-to-default button.

The CT-5624S board hardware and the boot loader support the

reset to default

button. If the reset button is continuously pushed for more than 5 seconds, the
boot loader will erase the entire configuration data saved on the flash memory.

NOTE:

Restoring system settings requires a system reboot. This necessitates

that the current Web UI session be closed and restarted. Before restarting the
connected PC must be configured with a static IP address in the 192.168.1.x
subnet in order to configure the CT-5624S.

After the Restore Default Configuration button is selected, the following screen
appears. Close the DSL Router Configuration window and wait for 2 minutes
before reopening your web browser. If necessary, reconfigure your PC's IP

address to match your new configuration.

- -

70

«
...
69
70
71
72
73
...
»

Содержание CT-5624S



























































































Отзывы:

Нет отзывов

Похожие инструкции для CT-5624S

Wireless Router

Бренд: Watchguard Страницы: 11

Бренд: D-Link Страницы: 32

Бренд: D-Link Страницы: 28

Бренд: D-Link Страницы: 48

Бренд: D-Link Страницы: 83

Бренд: D-Link Страницы: 155

Бренд: Makita Страницы: 2

Бренд: Observint Страницы: 117

PoleVault System A/V Source Inputs

Бренд: Extron electronics Страницы: 4

Бренд: Speedtouch Страницы: 124

Бренд: 8level Страницы: 52

Бренд: Rosewill Страницы: 3

Hotwire ATM Line Cards 8335

Бренд: Paradyne Страницы: 132

SmartMesh IA-510 D2511

Бренд: Dust Networks Страницы: 30

Бренд: Draytek Страницы: 2

Бренд: Genie Страницы: 6

3C8567 - SuperStack II NETBuilder SI 567...

Бренд: 3Com Страницы: 6

Бренд: Idis Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды