background image

Read Before Use

 

Congratulations! You have just purchased one of the finest pieces of playground equipment available. 
Your family will enjoy many hours of fun with this fine equipment. Playground equipment can be most 
enjoyable, but there are some dangers if not used properly. You should be aware of the following: 
 
Equipment should be installed in a level area, free from obstructions, with enough space to allow for 
adequate clearance in all directions when equipment is in maximum use. 
 
Keep objects away from equipment that could interfere with persons using it or that could be hazardous. 
 
Misuse or abuse of this playground equipment is dangerous and can cause serious injury. 
 
This equipment should be inspected before each use and any worn, defective or missing parts should be 
replaced. 
 
Children should play on equipment only with adult supervision and should be duly warned of the 
potential hazards in this type of equipment when used improperly. Children should be instructed as to 
proper caution to take in its use. 
 
Equipment should NOT be used when it is wet or icy. 
 
Equipment should only be used in a well-lighted area. 
 
Do NOT use equipment when tired, under stress or emotionally upset. 
 
Do NOT overcrowd. 
 
Do NOT use equipment when under the influence of alcohol or drugs. 
 
Do NOT attempt somersaults or gymnastic stunts on or using this equipment.  
 
Know your own limitations and exercise caution at all times. 
 
Do not jump off of equipment when dismounting. It is a dangerous practice to jump on or off equipment. 
 
Do not attempt to use equipment for something other than the use for which it was designed and intended, 
or in a manner other than that for which it was designed and intended. 

 
 
 

 
 
 
 
 
 

While every attempt is made by Component Playgrounds to ensure the highest degree of 

safety in all of our equipment, we cannot guarantee freedom from injury. The user 

assumes all risk of injury due to use. All merchandise is sold on this condition, which no 

representative of the company can waive or change

.

 

 

Содержание PH30 Swing Set



































Отзывы: