Compliance West HT-2000PR Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 41

background image

9

Testing Equipment with non-Standard Plugs or Pigtail Operation

The  front  panel  of  the  HT-PR  is  provided  with  a  NEMA  Type  5-15R  receptacle,  suitable  for
testing cord-equipped single-phase products designed for use on a 15 amp branch circuit in North
America.    For  other  types  of  products,  a  different  receptacle  type  or  pigtail  leads  may  be
required.  Various adapters and pigtail leads are available from Compliance West USA, or you
can  make  your  own,  just  make  sure  for  the  correct  configuration  see  the  description  of  the
outputs in the connections section.  If tests of this type are contemplated, call us for information.

«
...
13
14
15
16
17
...
»

Содержание HT-2000PR










































Отзывы:

Нет отзывов

Похожие инструкции для HT-2000PR

Бренд: Jackco Страницы: 6

Martin ERA 800 Performance

Бренд: Harman Страницы: 32

Martin ERA 600 Performance

Бренд: Harman Страницы: 32

Бренд: Hardt Страницы: 22

Бренд: Sabre Страницы: 2

Бренд: Yamaha Страницы: 46

Бренд: Nemalux Страницы: 6

Бренд: OBDLink Страницы: 2

Бренд: Kellfri Страницы: 12

Бренд: laerdal Страницы: 9

Бренд: Raymarine Страницы: 3

SmartPilot ST8002

Бренд: Raymarine Страницы: 48

Бренд: Raymarine Страницы: 38

hsb2 PLUS Series

Бренд: Raymarine Страницы: 248

Бренд: VDO Страницы: 15

Бренд: VDO Страницы: 20

Бренд: XFit Страницы: 16

BlackBox Series

Бренд: Nakamichi Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды