-19-
If setting lock-time as 00 means: swipe card or input password once to
open the door, swipe card or input password again to close the door.
Press the button to quit the setting mode.
In the setting mode:
Press the button and (mode indicator will flash yellow), follow
the button twice, (a continuous beep will be heard and mode indicator
will turn yellow), it indicates all user cards and codes have been cleaned
out successfully.
Press the button and (mode indicator will flash yellow), follow
the button twice, (a continuous beep will be heard and mode indicator
will turn yellow), it indicates it restores to factory defaults.
Press the button to quit the setting mode and standby.
If enter wrong information, it will imply as BI.BI. sounds. The device would
turn back without actions in 30 seconds automatically accompany with BI.
BI. sounds. If it is not in the setting mode and press incomplete numbers,
and if unlock door by card and password (combined) but only one action
is done, then it will turn back in 5s automatically accompany with BI.BI.
sounds.
Clean all user cards and codes, restores to factory defaults
In the setting mode:
Press the button and , the mode indicator will flash yellow,
enter the number from 00 to 99, the mode indicator will turn yellow in
the mean time a long beep will be heard, it indicates a success of
delay time setting. 00-99 means the delay time, eg. 05 means the
unlocking time is 5s delayed. If setting lock-time as 00 means: swipe
card or input password once to open the door, swipe card or input
password again to close the door.
Press the button to quit the setting mode.
Set the unlocking time for ZONE 1
In the setting mode:
Press the button and , the mode indicator will flash yellow, enter
the number from 00 to 99, the mode indicator will turn yellow in the mean
time a long beep will be heard, it indicates a success of delay time setting.
00-99 means the delay time, eg. 05 means the unlocking time is 5s delayed.
Set the unlocking time for ZONE 2
-20-
In the setting mode:
Press the button and , the yellow LED indicator will be flashing,
then input a new administrator code twice(The length of the new admin
code must as same as the old one) and a
Press the button to quit the setting mode.
sounds "BI" means modify
successfully.
Modify administrator code
In the setting mode:
Press the button and (mode indicator will flash yellow), follow
with the and , a long beep will be heard whilst the mode indicator
will turn yellow, pickproof alarm is turned off.
Press the button and (mode indicator will flash yellow), follow
with the and , a long beep will be heard whilst the mode indicator
will turn yellow, pickproof alarm is turned on.
Press the button to quit the setting mode.
Turn on/off the pickproof alarm
In case forget the a
dmin c ode, p ress t he b utton a nd h old o n, t hen
power on(Notice: DH16A-20DT/DTQ DH16A-32DT/DTQ, power on first,
then press the button in 3s). A sound "BI" as reminder, means admin
code default setting successfully.
Digit length is 2--default admin code is 12,
Digit length is 3--default admin code is 123,
Digit length is 4-default admin code is 1234,
Digit length is 5--default admin code is 12345,
Digit length is 6--default admin code is 123456(Maxmium is 6).
A. When ZONE 1 relay actived, door indicator will turn green.
B. When ZONE 2 relay actived, door indicator will turn red.
sensor is directly exposed into the light. The buzzer will be off
automatically in 60 seconds when the light is no longer detected, or by
entering the admin code.
The built-in buzzer will send a continuous beeping if the photoresistor
The pickproof alarm
Содержание DH16A-10DT
Страница 2: ......
