Compaq AP400 - Professional - 64 MB RAM Скачать руководство пользователя страница 60

Страница: 60 / 74

Further Troubleshooting

Network Problem

Continued

Problem

Possible Solution

Network controller stopped
working when an expansion
board was added to the
computer.

1. Network drivers are not loaded or driver parameters do not match

the current configuration. Make sure that the drivers are loaded and
that the driver parameters match the configuration of the network
controller.

2. The cable is not securely connected or is attached incorrectly.

Ensure that the cable is securely attached to the network connector
and that the other end of the cable is securely attached to the correct
device.

3. Network controller interrupt with an expansion board. Under the

Computer Setup Advanced menu, change the resource settings for
the board.

4. Network drivers were accidentally deleted when the drivers for the

new expansion board were installed, or the files containing the
network drivers are corrupted. Reinstall the network drivers, using
backup diskettes.

Network controller stopped
working without apparent cause.

1. The files containing the network drivers are corrupted. Reinstall the

network drivers, using backup diskettes.

2. The cable is not securely connected or is attached incorrectly.

Ensure that the cable is securely attached to the network connector
and that the other end of the cable is securely attached to the correct
device.

3. The network controller is defective. Replace the network controller or

system board.

Cannot connect to the network
server when attempting Remote
System Installation.

The network controller is not configured properly. Run Computer
Setup and modify the Embedded NIC Settings.

System Setup utility reports
unprogrammed EPROM.

1. Boot the workstation without the network drivers using a system boot

diskette and reconfigure the controller.

2. Replace the controller.

3. Replace the system board.

Содержание AP400 - Professional - 64 MB RAM











































































Результаты поиска

Содержание AP400 - Professional - 64 MB RAM

Отзывы:

Бренды по названию

Популярные бренды

Compaq AP400 - Professional - 64 MB RAM, Руководство по устранению неисправностей

Результаты поиска

Содержание AP400 - Professional - 64 MB RAM

Отзывы:

Бренды по названию

Популярные бренды