Compaq 158222-B21 - StorageWorks Fibre Channel SAN Switch 8 Скачать руководство пользователя страница 1

Compaq StorageWorks

Fibre Channel 
Switch, 8-/16-Port 
Universal 
Mounting Kit

 

Open Card Completely Before 
Beginning Installation Procedures

© 2001 Compaq Information Technologies Group, L.P.
Compaq, the Compaq logo, and StorageWorks are trademarks of Compaq 
Information Technologies Group, L.P. 
All other product names mentioned herein may be trademarks of their 
respective companies.
Compaq shall not be liable for technical or editorial errors or omissions 
contained herein. The information is provided “as is” without warranty of 
any kind and is subject to change without notice. The warranties for 
Compaq products are set forth in the express limited warranty statements 
accompanying such products. Nothing herein should be construed as 
constituting an additional warranty.
Printed in the U.S.A.

Fibre Channel Switch, 8-/16-Port Universal Mounting Kit
Third Edition (November 2001)
Part Number: EK-GGAAB-IA. C01
Compaq Computer Corporation

About This Card

This card identifies the contents of the universal mounting kit 
and provides procedures for mounting Fibre Channel 8-port 
(380591–B21/ DS–DSGGA–AA or 176219–B21/
DS–DSGGC–AA) and 16-port (380578–B21/
DS–DSGGA–AB or 212776–B21/DS–DSGGC–AB) switches 
into the following Compaq racks:

RETMA 41U or 42U

Compaq Classic

Metric SW600

Kit Contents

NOTE:  

This kit contains parts for multiple rack installations. Not all kit parts 

are needed for all rack installations.

1

Mounting brackets (2)

2

Extender brackets (2)

3

Slide brackets (2)

4

Bag of miscellaneous hardware:

Snap-on cable ties (2)

Clip nuts (4)

Alignment washers (8)

Pan head SEMS screws, 10-32 x 9/32 inches (4)

Pan head SEMS screws, 10-32 x 5/8 inches (16)

Flat washers for #10 screws (4)

Pan head SEMS screws, 8-32 x 1/4 inches (4)

Flat washers for #8 screws (4)

Tools Required

No. 2 Phillips screwdriver

1

2

3

4

CXO7467B

Содержание 158222-B21 - StorageWorks Fibre Channel SAN Switch 8








Отзывы: